manualshive.com logo in svg

Ford 2011 Taurus, Owner'S Manual

The Ford 2011 Taurus Owner's Manual is a comprehensive guide that provides essential information on operating, maintaining, and troubleshooting your vehicle. Available for free download at manualshive.com, this manual offers clear instructions, diagrams, and tips to ensure a smooth and enjoyable driving experience.

Share
Download
background image

The heated seats only operate when the ignition is on. To operate the
heated seats:

•

Press the indicated side of the
control for maximum heat.

•

Press again to deactivate.

•

Press the indicated side of the
control for minimum heat.

•

Press again to deactivate.

The heated seat module resets at every ignition run cycle. While the
ignition is in the on position, activating the high or low heated seat
switch enables heating mode. When activated, they will turn off
automatically when the engine is turned off.

The indicator light will illuminate when the heated seats have been
activated.

SAFETY RESTRAINTS

Personal Safety System™

The Personal Safety System provides an improved overall level of frontal
crash protection to front seat occupants and is designed to help further
reduce the risk of airbag-related injuries. The system is able to analyze
different occupant conditions and crash severity before activating the
appropriate safety devices to help better protect a range of occupants in
a variety of frontal crash situations.

Your vehicle’s Personal Safety System consists of:

•

Driver and passenger dual-stage airbag supplemental restraints.

•

Front outboard safety belts with pretensioners, energy management
retractors (first row only), and safety belt usage sensors.

•

Driver’s seat position sensor.

•

Front passenger sensing system

Seating and Safety Restraints

157

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2011 Taurus

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Taurus

Raven CR7 Calibration Manual preview
CR7
Brand: Raven Pages: 24
Weather Guard 237 Assembly And Installation Instructions preview
237
Brand: Weather Guard Pages: 4
Eclipse AVN 2210p mkII Operation Manual preview
AVN 2210p mkII
Brand: Eclipse Pages: 6
IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Brand: IAME Pages: 17
Axxess AX-AM-AU92 Installation Instructions Manual preview
AX-AM-AU92
Brand: Axxess Pages: 8
WABCO TP2205 Installation Manual preview
TP2205
Brand: WABCO Pages: 48
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Brand: Chevrolet Pages: 412
KEKO K617 Installation Description preview
K617
Brand: KEKO Pages: 3
Movon MDAS-5 Installation Manual preview
MDAS-5
Brand: Movon Pages: 43
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Brand: Thule Pages: 12
BENDIX A-18 TRAILER ABS Manual preview
A-18 TRAILER ABS
Brand: BENDIX Pages: 40
Toyota RAV4 HV 2016 Quick Reference Manual preview
RAV4 HV 2016
Brand: Toyota Pages: 56
Ford Mustang 2007 Supplement Manual preview
Mustang 2007
Brand: Ford Pages: 40
Prorack K374 Manual preview
K374
Brand: Prorack Pages: 14
Fleetwood Bounder turbo diesel 2001 Instructions Manual preview
Bounder turbo diesel 2001
Brand: Fleetwood Pages: 166
Toyota 1998 Celica Owner'S Manual preview
1998 Celica
Brand: Toyota Pages: 204
Quadratec QuadraTop Adventure Top S Manual preview
QuadraTop Adventure Top S
Brand: Quadratec Pages: 13
Blitz BZCAPT30 User Manual preview
BZCAPT30
Brand: Blitz Pages: 4

Brands by name

Popular brands

Load more brands