Ford 2011 Taurus Page 21 Owner'S Manual Download | Manualshive

Page: 21 / 408

background image

To operate, do the following:

1. Press and release RESET in order to start the timer.

2. Press and release RESET to pause the timer.

3. Press and hold RESET until the timer resets.

Blank Screen

The message center display will be blank after cycling through all of the
Info menu items.

System check and vehicle feature customization

Press the SETUP button repeatedly
to cycle the message center through
the following features:

RESET FOR SYSTEM CHECK

When this message appears, press RESET and the message center will
begin to cycle through the following systems and provide a status of the
item if needed.

Note:

Some systems show a message only if a condition is present.

1. OIL LIFE

2. WASHER FLUID LEVEL

3. DOOR AJAR STATUS

4. TRUNK AJAR/CLOSED

5. BLIND SPOT SYSTEM (if equipped)

6. CROSS TRAFFIC SYSTEM (if equipped)

7. BRAKE SYSTEM

8. FUEL LEVEL

9. MYKEY DISTANCE (if MyKey

威

is programmed)

10. MYKEY(S) PROGRAMMED

11. ADMIN KEYS PROGRAMMED

OIL LIFE

This displays the remaining oil life.

An oil change is required whenever indicated by the message center and
according to the recommended maintenance schedule. USE ONLY
RECOMMENDED ENGINE OILS.

Instrument Cluster

21

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

«
...
19
20
21
22
23
...
»

Summary of Contents for 2011 Taurus

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Taurus

Brand: Calira Pages: 14

Brand: Wagan Pages: 12

Brand: Vaisala Pages: 24

Brand: Carax Pages: 2

Brand: Yakima Pages: 11

Brand: NanoCam Plus Pages: 32

Quantum Wash'n'Wipe N30208

Brand: National Cycle Pages: 12

Security Cage Kit

Brand: Toro Pages: 8

Brand: JBA Pages: 5

CommCenter 300MB-SD

Brand: Federal Signal Corporation Pages: 60

EVO ONE THAR-GM7

Brand: Fortin Pages: 11

Brand: TOP VEHICLE TECH Pages: 8

Brand: Prorack Pages: 17

Brand: Kia Pages: 17

Brand: Snapper Pages: 8

2013 Duramax Diesel

Brand: Chevrolet Pages: 132

Brand: MeiTrack Pages: 15

Brand: PAC Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands