Ford 2011 Taurus Page 182 Owner'S Manual Download | Manualshive

Page: 182 / 408

background image

The fact that the airbags did not inflate in a collision does not mean that
something is wrong with the system. Rather, it means the forces were
not of the type sufficient to cause activation. Side airbags are designed
to inflate in side-impact collisions, not roll-over, rear-impact, frontal or
near-frontal collisions, unless the collision causes sufficient lateral
deceleration.

WARNING:

Several air bag system components get hot after

inflation. Do not touch them after inflation.

WARNING:

If the side

airbag has deployed,

the

airbag will not function again.
The side airbag system
(including the seat) must be
inspected and serviced by an
authorized dealer.

If the airbag

is not replaced, the unrepaired
area will increase the risk of injury
in a collision.

Safety Canopy

姞

System

WARNING:

Do not place

objects or mount equipment

on or near the headliner at the
siderail that may come into
contact with a deploying Safety
Canopy

威

. Failure to follow these

instructions may increase the risk
of personal injury in the event of a
collision.

WARNING:

Do not lean your head on the door. The Safety

Canopy

威

could injure you as it deploys from the headliner.

Seating and Safety Restraints

182

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

«
...
180
181
182
183
184
...
»

Summary of Contents for 2011 Taurus

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Taurus

Brand: iDataLink Pages: 9

Brand: VanEssa mobilcamping Pages: 8

Brand: RaceChip Pages: 12

Brand: Ford Pages: 37

Brand: Rati Pages: 2

Brand: Würth Pages: 36

Brand: StowAway 2 Pages: 2

Brand: BURY Pages: 2

Brand: Subaru Pages: 540

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

Brand: EUFAB Pages: 20

Brand: Ranger design Pages: 22

Brand: Pyle Pages: 14

Brand: RADICAL Pages: 11

Brand: Feniex Pages: 4

Brand: STO N SHO Pages: 7

Brand: EZ-ON Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands