Ford 2011 Taurus Page 197 Owner'S Manual Download | Manualshive

Page: 197 / 408

background image

The tether strap anchors in your
vehicle are in the following positions
(shown from top view):

Attach the tether strap only to the appropriate tether anchor as shown.
The tether strap may not work properly if attached somewhere other
than the correct tether anchor.

Once the child safety seat has been installed, using either the safety belt,
the lower anchors of the LATCH system, or both, you can attach the top
tether strap.

If you install a child seat with rigid LATCH attachments, and have
attached the top tether strap to the proper top tether anchor, do not
tighten the tether strap enough to lift the child seat off the vehicle seat
cushion when the child is seated in it. Keep the tether strap just snug
without lifting the front of the child seat. Keeping the child seat just
touching the vehicle seat gives the best protection in a severe crash.

Perform the following steps to attach a child safety seat to the tether
anchor:

1. Route the child safety seat tether strap over the back of the seat.

For vehicles with adjustable head restraints, route the tether strap under
the head restraint and between the head restraint posts, otherwise route
the tether strap over the top of the head restraint.

2. Locate the correct anchor for the
selected seating position.

Seating and Safety Restraints

197

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

«
...
195
196
197
198
199
...
»

Summary of Contents for 2011 Taurus

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Taurus

Brand: iDataLink Pages: 30

Brand: Neuspeed Pages: 2

Brand: Gator Pages: 2

Brand: Xblitz Pages: 30

Brand: Harman Kardon Pages: 16

Brand: TATA Motors Pages: 184

PW-50C Civilian

Brand: B&G electronics Pages: 7

Truck Diesel Supplement 2012

Brand: RAM Pages: 174

Brand: Quadratec Pages: 6

Brand: Gator Pages: 6

Brand: Yakima Pages: 12

Brand: rough country Pages: 4

Brand: Volvo Pages: 197

Brand: Seat Pages: 300

Brand: NavLinkz Pages: 26

Brand: Technaxx Pages: 59

Brand: Snapper Pages: 8

GM DELTA 88 1974

Brand: Oldsmobile Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands