Ford 2011 Taurus Page 128 Owner'S Manual Download | Manualshive

Page: 128 / 408

background image

•

after 25 seconds of illumination.

The lights will not turn off if:

•

they have been turned on with the dimmer control, or

•

any door is open.

Illuminated exit

When all vehicle doors are closed, the ignition is turned off and the key
is removed from the ignition (IKT only), the interior dome lamps,
parking lamps and the puddle lamps (if equipped) will illuminate.

The lamps will turn off if all the doors remain closed and

•

25 seconds elapse, or

•

the key is inserted in the ignition (IKT only) or (if equipped with
intelligent access with push button start feature) the start button is
pressed.

Battery saver

The battery saver will shut off the lamps 10 minutes after the ignition
has been turned off.

•

If the dome lamps were turned on using the panel dimmer control, the
battery saver will shut them off 10 minutes after the ignition has been
turned off.

•

If the courtesy lamps were turned on because one of the vehicle doors
or the trunk was opened, the battery saver will shut them off
10 minutes after the ignition has been turned off.

•

The battery saver will shut off the headlamps 10 minutes after the
ignition has been turned off.

Accessory mode battery saver for intelligent access keys with
push button start (if equipped)

If you shut off the engine and leave the ignition in the on or accessory
mode, the ignition will shut off after 30 minutes.

Locks and Security

128

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

«
...
126
127
128
129
130
...
»

Summary of Contents for 2011 Taurus

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Taurus

Brand: Valeo Pages: 17

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

DAF POWERCHOICE 250A

Brand: Paccar Pages: 20

YARIS LIFTBACK 2009

Brand: Toyota Pages: 13

Brand: Westfalia Pages: 71

Brand: Whispbar Pages: 15

Green Motion DC 66

Brand: Eaton Pages: 18

Escalade ESV 2014

Brand: Cadillac Pages: 508

Brand: Hama Pages: 2

Brand: Toro Pages: 24

Brand: UAZ Pages: 90

Brand: BMW Pages: 189

1999 Crown Victoria

Brand: Ford Pages: 208

Brand: Volvo Pages: 16

DH-RB 05.02 Series

Brand: Dhollandia Pages: 65

Brand: Ford Pages: 8

Brand: Nav TV Pages: 11

Brand: Conrad Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands