Ford 2011 Taurus Page 257 Owner'S Manual Download

Page: 257 / 408

P (Park)

This position locks the transmission
and prevents the front wheels from
turning.

To put your vehicle in gear:

•

Press the brake pedal

•

Move the gearshift lever into the
desired gear

To put your vehicle in P (Park):

•

Come to a complete stop

•

Move the gearshift lever and
securely latch it in P (Park)

WARNING:

Always set the parking brake fully and make sure

the gearshift is latched in P (Park). Switch the ignition off and

remove the key whenever you leave your vehicle.

R (Reverse)

With the gearshift lever in R (Reverse), the vehicle will move backward.
Always come to a complete stop before shifting into and out of R
(Reverse).

N (Neutral)

With the gearshift lever in N (Neutral), the vehicle can be started and is
free to roll. Hold the brake pedal down while in this position.

D (Drive)

The normal driving position for the best fuel economy. Transmission
operates in gears one through six.

Driving

257

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2011 Taurus

























































































































































































































































































































































































































Search results

Summary of Contents for 2011 Taurus

Reviews:

Related manuals for 2011 Taurus

Brands by name

Popular brands

Ford 2011 Taurus, Owner'S Manual

Search results

Summary of Contents for 2011 Taurus

Reviews:

Related manuals for 2011 Taurus

Brands by name

Popular brands