Flo CoRe+ Installation Manual Download | Manualshive

Page: 36 / 52

background image

36

OR

6.4.2.2.

Before Installing a Cable Management System on an Existing

Side-by-Side Charging Station Installation

1.

Prepare the installation material for the side-by-side charging station mount brackets and cable

management systems and follow the instructions below.

6.4.3.

Installing the Cable Management System and

Supports

1.

Assemble the flexible tube.

2.

Remove the plate allowing you to access the electrical wires at the bottom of the pedestal and leave
10’’ (30 cm) of extra wiring to connect the charging station once the flexible tube has been installed.

3.

Screw the end of the flexible tube to the charging station mounting bracketing on the pedestal side.

4.

Pass the wires through the flexible tube.

5.

Screw the first charging station mount bracket to the pedestal.

CAUTION

: This pedestal is certified as an electrical enclosure, and any alteration must comply

with local regulations.

«
...
34
35
36
37
38
...
»

Summary of Contents for CoRe+





















































Reviews:

No comments

Related manuals for CoRe+

Brand: UFESA Pages: 27

Brand: AA Products Pages: 6

Brand: AA Products Pages: 8

Brand: Kargo Master Pages: 6

Brand: OBH Nordica Pages: 28

Brand: IFO Pages: 8

Brand: Warrior Products Pages: 2

Brand: Oki Pages: 2

Brand: OKIDATA Pages: 16

Brand: PAC Pages: 4

Brand: PAC Pages: 4

SX-70 SODR-X-TRACTOR

Brand: Pace Pages: 2

Brand: PAC Pages: 8

Brand: PAC Pages: 5

Brand: Waterpik Pages: 2

Brand: Kabuto Pages: 12

Reference Series

Brand: OEM Audio Pages: 29

Brand: XCM Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands