FlexiForce ForceIQ Force100XC Manual Download Page 15

Page: 15 / 42

manual – force

www.flexiforce.com

6) Inv. profile up

Only for inverter operator

Use the

buttons to adjust the following parameters:

•

Max speed

(Hz

)

the maximum speed after acceleration

•

Min speed (Hz)

the speed after deceleration

•

Start ramp (ms)

acceleration time

•

Slowdown slope (ms)

deceleration time

•

Stop ramp (Incr.)

value before the end position were the slope has to start

Press to return to the main menu. Press once more to return to the manoeuvring mode

7) Inv. profile down

Only for inverter operator

Use the

buttons to adjust the following parameters:

•

Max speed

(Hz

)

the maximum speed after acceleration

•

Slow speed (Hz)

the speed after deceleration

•

Medium speed (Hz)

the speed after reach position medium speed (see point 8 page 14)

•

Start ramp (ms)

acceleration time

•

Slowdown slope (ms)

deceleration time

•

Stop ramp (Incr.)

value before the end position were the slope has to start

Fu profile boost

Only for inverter operator

Use the

buttons to adjust the following parameters:

•

Rated frequency (Hz)

nominal frequency of the motor

•

Boost (%)

to increase the voltage by low frequency

Summary of Contents for ForceIQ Force100XC











































Search results

Summary of Contents for ForceIQ Force100XC

Reviews:

Related manuals for ForceIQ Force100XC

Brands by name

Popular brands

FlexiForce ForceIQ Force100XC, Manual

Search results

Summary of Contents for ForceIQ Force100XC

Reviews:

Related manuals for ForceIQ Force100XC

Brands by name

Popular brands