background image

3-11  Auxiliary settings – The Auxiliary settings adds five additional independent auxiliary outputs for a total  
 

of seven with this option turned on. Special Option Group 1 allows for independent timing of these    

 

outputs. 

3-15   Soft Disarm - When a vehicle has factory security, and the Firstech alarm is triggered, you may have   
 

both alarms sounding at the same time. In the default setting, silencing the Firstech system will not 

 

shut down the factory system, therefore requiring the user to first silence the Firstech system (by tap   

 

ping unlock 1 time) and then unlock a 2nd time to silence the factory system. Option2 will send the  

 

Factory Alarm Disarm (orange white wire CN3 or any other POC programmed as FAD) and 5  

 

 

seconds later sends rearm pulse (orange wire CN3) to ensure the doors re-lock if needed. 

3-16  RPS - This option changes the between the option RPS 2 or the new RPS Touch. Please see the  

 

 

Placement and Use of Components section of this manual for details.

4-01  Aux 1 Output  - This feature determines the duration of the auxiliary 1 output. (Option 4 allows the  
 

output duration to be set for a specific length of time 1-99 sec. only available when using the  

 

 

OP500)

4-02  Aux 2 Output  - This Feature determines the duration of the auxiliary 2 output. (Option 4 allows the  
 

output duration to be set for a specific length of time 1-99 sec. only available when using the  

 

 

OP500)

4-03  Aux 1 Output Control - This feature allows the user to configure the method of which Auxiliary 1 can  
 

be activated. (Option 4 will activate AUX 1, for a set period of time based off of feature 4-01, as  

 

 

soon as ignition input to the CM is removed)

4-04  Aux 2 Output Control - This feature allows the user to configure the method of which Auxiliary 2 can  
 

be activated. (Option 4 will activate AUX 2, for a set period of time based off of feature 4-02, as  

 

 

soon as the CM receives the start command)

4-05  Secure Aux Output – This feature, in the default option should help prevent accidental activation of    
 

the AUX outputs. (2way remotes will require button IV or start button to be tapped before activating    

 

any of the AUX outputs. 1way remotes require the user to hold  trunk+start buttons for 2.5 seconds    

 

before activating AUX outputs Option setting II turns this feature off.)

4-06  Aux 1 Input – This feature changes the input behavior of the pre-warn wire on the Aux Input Sensor    
 

green connector.

 

Default 1: Will pre-warn with a negative (-) ground input.

 

Option 2: Will instant trigger with a negative (-) ground input.

           Option 3: Will disarm the alarm with a negative (-) ground input. Used when adding an alarm to a    
 

factory keyless entry system.

 

Option 4: Changes the output into an open circuit input.

CM6300

 

Install Guide

Alarm System

www.firstechonline.com | www.compustar.com

Copyright 2012 Firstech, LLC.

Page 25

Summary of Contents for CM6300

































Reviews: