Fike DuraQuench, Design, Installation, Operation, And Maintenance Manual

Page: 27 / 94

P/N 06 ‐ 791 ‐ 4 (Rev. 4) Page 19
704 SW 10
th
Street, P.O. Box 610, Blue Springs, Missouri 64013 ‐ 0610 U.S.A. ● Phone: (816) 229 ‐ 3405 ● www.fike.com
Motor and Pump Specifications
Skid P/N 02 ‐ 14909 ‐ 1 ‐ X ‐ X 02 ‐ 14909 ‐ 2 ‐ X ‐ X 02 ‐ 14909 ‐ 3 ‐ X ‐ X 02 ‐ 14909 ‐ 4 ‐ X ‐ X 02 ‐ 14909 ‐ 5 ‐ X ‐ X 02 ‐ 15270 (Jockey)
3 ‐ Phase AC Standard Motors
Motor Type BALDOR BALDOR BALDOR BALDOR BALDOR ML80CA
Rated Power – P2 7.5 kW (10 HP) 11 kW (15 HP) 18.5 kW (25 HP) 11 kW (15 HP) 18.7 kW (25 HP) 1.12 kW (1.5 HP)
Mains Frequency 60Hz 60Hz 60Hz 50Hz 50Hz 50/60Hz
Rated Voltage (V) 3 x 208 ‐ 230/460* 3 x 208 ‐ 230/460* 3 x 230/460* 3 x 380 ‐ 415* 3 x 200/400
3 x 220 ‐ 240/
380 ‐ 415 (50Hz)
3 x 220 ‐ 255/
380 ‐ 440 (60Hz)
Rated Current (A) 24.8 ‐ 23.8/11.9 38 ‐ 35/17.5 56/28 20.2 ‐ 18.6 64/32
4.35/2.50 (50Hz)
4.15 ‐ 4.00/
2.40 ‐ 2.30 (60Hz)
Rated Speed (rpm) 3525 3520 3530 2930 2920
2840 ‐ 2870 (50Hz)
3420 ‐ 3470 (60Hz)
Motor Locked ‐ Rotor
Code (KVA/HP)**
K
(8.0 ‐ 8.99)
G
(5.6 ‐ 6.29)
J
(7.1 ‐ 7.99)
H
(6.3 ‐ 7.09)
H
(6.3 ‐ 7.09)
A
(0 ‐ 3.14)
Grundfos Pumps
Type CRN10 ‐ 12 CRN10 ‐ 14 CRN20 ‐ 10 CRN15 ‐ 12 CRN32 ‐ 10 CR1S ‐ 17
Pump Speed**** 3,470 rpm 3,470 rpm 3,521 rpm 2,924 rpm 2,934 rpm 3,463 rpm
Rated Flow
(duty point)
53.27 gpm
(201.6 lpm)
53.27 gpm
(201.6 lpm)
111.39 gpm
(421.70 lpm)
74.85 gpm
(283.3 lpm)
132.09 gpm
(500 lpm)
4.8 gpm
(18.3 lpm)
Rated Head
446.5 ft.
(136 m)
512.5 ft.
(156 m)
561.4 ft.
(171 m)
444.9 ft.
(136 m)
500.3 ft.
(152.5 m)
318 ft.
(97 m)
Maximum Head
577.4 ft.
(176 m)
669.3 ft.
(204 m)
698.8 ft.
(213 m)
554.5 ft.
(169 m)
638.5 ft.
(194.6 m)
478.7 ft.
(145.7 m)
Maximum Ambient
Temperature
140°F
(60°C)
104°F
(40°C)
104°F
(40°C)
104°F
(40°C)
104°F
(40°C)
140°F
(60°C)
Maximum Pressure
at Stated Temp
363 psi / 248°F
(25 bar / 120°C)
363 psi / 248°F
(25 bar / 120°C)
363 psi / 248°F
(25 bar / 120°C)
363 psi / 194°F
(25 bar / 90°C)
435 psi / 194°F
(30 bar / 90°C)
232 psi / 248°F
(16 bar / 120°C)
Maximum Inlet
Pressure***
100 psi
(6.9 bar)
100 psi
(6.9 bar)
100 psi
(6.9 bar)
100 psi
(6.9 bar)
100 psi
(6.9 bar)
100 psi
(6.9 bar)
Liquid Temp. Range
‐ 4 to +248 °F
( ‐ 20 to +120 °C)
‐ 4 to +248 °F
( ‐ 20 to +120 °C)
‐ 4 to +248 °F
( ‐ 20 to +120 °C)
‐ 4 to +194 °F
( ‐ 20 to +90 °C)
‐ 4 to +248 °F
( ‐ 20 to +120 °C)
‐ 4 to +248 °F
( ‐ 20 to +120 °C)
*Usable at 208 Volts.
**The motor’s inrush current, also known as locked ‐ rotor amps or LRA, can be calculated by inserting the KVA/HP value into the following formula:
LRA = KVA/HP x Motor HP x 1000 / 1.732 x Motor Voltage
***Current inlet pressure + churn (no flow) pressure must always be lower than the maximum permissible system operating pressure to prevent
potential damage to the bearing in the motor or reduced life of the shaft seal.
****Pump speed on which data is based.