FiberHome CiTRANS R820 Hardware Description Download Page 9

Page: 9 / 126

Conventions

Terminology Conventions

Terminology

Convention

CiTRANS R820

FiberHome CiTRANS R820 Edge Router

OTNM2000

FiberHome e-Fim OTNM2000 Element Management

System

SCUS1

Router System Control Unit

SCUS2

Router System Control Unit2

SCUS3

Router System Control Unit3

MSS1

Octal Port Ethernet Mixed Interface Card

MSS2

Four Port Ethernet Mixed Interface Card

MSS3

Two Port Ethernet Mixed Interface Card

E1S1

16 E1 Line Card with CES

PWRS1

Power Supply Terminal Card

FAN

FAN Control Card

Symbol Conventions

Symbol

Convention

Description

Note

Important features or operation guide.

Caution

Possible injury to persons or systems, or cause traffic

interruption or loss.

Warning

May cause severe bodily injuries.

➔

Jump symbol

Jump to another step.

→

Cascading

Cascade multiple-level menu options.

↔

Bi-directional

service

The service signal is bi-directional.

→

Unidirectional

service

The service signal is unidirectional.

III

Summary of Contents for CiTRANS R820































































































































Search results

Summary of Contents for CiTRANS R820

Reviews:

Related manuals for CiTRANS R820

Brands by name

Popular brands

FiberHome CiTRANS R820, Hardware Description

Search results

Summary of Contents for CiTRANS R820

Reviews:

Related manuals for CiTRANS R820

Brands by name

Popular brands