FiberHome CiTRANS R820 Hardware Description Download Page 116

Page: 116 / 126

CiTRANS R820 Edge Router Hardware Description

Table D-2

Indicators on the Fan Control Card (Continued)

Indicator

Meaning

Description

OFF: The fan control card does not have any

alarm.

D.3

Indicators on Cards

Indicators on a card indicate the operating status and alarm status of the card.

Table D-3

Indicators on Cards

Indicator

Meaning

Description

ACT

Card operating indicator

Blinking quickly (green): The card is operating

normally.

OFF: The card is not operating normally.

ON (green): The card is not operating normally, or

communication between the card and the

OTNM2000 is not smooth.

Critical alarm indicator

OFF: The card does not have any critical alarm, or

all the critical alarms are filtered.

ON (red): The card has a critical or major alarm.

NUA

Minor alarm indicator

OFF: The card does not have any minor alarm, or

all the minor alarms are filtered.

ON (yellow): The card has a minor alarm.

Table D-4

Indicators on the Panel of the SCUS1/2/3 Card

Indicator

Meaning

Description

ACT

Card operating indicator

Blinking quickly: The card is operating normally.

Blinking slowly: The card is standby.

OFF: The card is not operating normally.

ON (green): The card is not operating normally, or

not communicating smoothly with the EMS.

Critical alarm indicator

OFF: The local NE does not have any critical alarm,

or all the critical alarms are filtered.

ON (red): The local NE has a critical or major alarm.

NUA

Non-critical alarm

indicator

OFF: The local NE does not have any non

—

critical

alarm, or all the non

—

critical alarms are filtered.

ON (yellow): The local NE has a non

—

critical

alarm.

D-2

Version: A

Summary of Contents for CiTRANS R820































































































































Search results

Summary of Contents for CiTRANS R820

Reviews:

Related manuals for CiTRANS R820

Brands by name

Popular brands

FiberHome CiTRANS R820, Hardware Description

Search results

Summary of Contents for CiTRANS R820

Reviews:

Related manuals for CiTRANS R820

Brands by name

Popular brands