manualshive.com logo in svg

Festo IFB05-03, Manual

Share
Download
Festo IFB05-03 Manual Download Page 54

3.      Installation

3−20

Festo    P.BE−VIFB5−03−EN    en  0503e

Potential  equalization

The  valve  terminal  has  two  earth  connections  for  potential
equalization.

on  the  load  voltage  connection  (pin  4  incoming  socket).

on  the  left−hand  end  plate  (M4  thread).

Please  note

S

Always  connect  the  earth  potential  to  pin  4  of  the  volt
age  connection.

S

Connect  the  earth  connection  of  the  left−hand  end  plate
to  the  earth  potential  with  low  impedance  (short  cable
with  large  cross−sectional  area).

S

By  means  of  low−impedance  connections,  you  can  be
sure  that  the  housing  of  the  valve  terminal  and  the  earth
connection  at  pin  4  have  the  same  potential  and  that
there  are  no  equalizingcurrents.

You  can  thereby  avoid  interference  due  to  electromagnetic
influences  and  you  can  ensure  electromagnetic  compatibil
ity  in  accordance  with  the  EMC  guidelines.

Summary of Contents for IFB05-03



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands