Festo IFB05-03 Manual Download Page 32

Page: 32 / 154

2. Fitting

2−8

Festo P.BE−VIFB5−03−EN en 0503e

Proceed as follows:

1. Ascertain the weight of your valve terminal as described

in chapter 2.3

2. Make sure that the mounting surface can support this

weight.

3. Fit a hat rail (support rail as per EN 50022 − 35x15;

width35 mm, height 15 mm).

4. Fasten the hat rail to the fastening surface at least every

100mm.

5. Hang the valve terminal onto the hat rail. Fasten the valve

terminal on both sides with the hat−rail clamping unit to
prevent it from tilting or sliding (see Fig.2/3).

6. If the hat−rail clamping unit is subject to vibration or if it is

fitted in a sloping position, fasten it with two locking
screws (item 3) against unintentional loosening/opening.

Hat−rail clamping
unit unlocked

Hat−rail clamping
unit locked

Locking screw

Fig.2/3: Fitting the type 03 valve terminal to a hat rail

Summary of Contents for IFB05-03



























































































































































Search results

Summary of Contents for IFB05-03

Reviews:

Brands by name

Popular brands

Festo IFB05-03, Manual

Search results

Summary of Contents for IFB05-03

Reviews:

Brands by name

Popular brands