Festo IFB05-03 Manual Download Page 14

Page: 14 / 154

Contents and general instructions

XII

Festo P.BE−VIFB5−03−EN en 0503e

The  valve  terminals  can  be  connected  to  the  controllers  of
various  manufacturers.  This  manual  deals  with  the  configur
ation  of  the  PLC  and  the  addressing  of  the  terminals  for  the
following  control  systems:

Controller
manufacturer

Controller (PLC)

field bus module

Field bus

Festo

FPC 405
SF−202 types

02...05

SF3 types

02...05

E.CFA
integrated
integrated

Festo field bus

ABB

ABB  Procontic
CS31  (connected
directly  to  the  cen
tral  unit)

ABB Procontic T200

Central  unit  07KR91
Central  unit  07KR31
Central  unit  07KT92
Central  unit  07KT93

Coupler 07CS61

ABB

CS31 system bus

Klöckner−Moeller

SUCOS  PS  30  series
e.g.
PS  416
PS  4−201

Serial bus interface

integrated
integrated

SucoNet K

Fig.0/5: Automation systems/field bus protocols which can be connected

Please note

ABB

The address range of 64 I/Os can be used as from soft
ware version 1.3 (SW 23.01.95 or later).

Klöckner−Moeller

The protocol for use on the SUCOnet K can be used as
from software version 1.4 (SW 21.03.96 or later).

See type plate of valve terminal

Summary of Contents for IFB05-03



























































































































































Search results

Summary of Contents for IFB05-03

Reviews:

Brands by name

Popular brands

Festo IFB05-03, Manual

Search results

Summary of Contents for IFB05-03

Reviews:

Brands by name

Popular brands