Festo IFB05-03 Manual Download Page 106

Page: 106 / 154

5. Diagnosis and error treatment

5−12

Festo P.BE−VIFB5−03−EN en 0503e

Starting the test routine

1. Switch off the operating and load voltage supplies (pins 1

and 2).

2. Open the node in accordance with chapter 3.2.1, Open

ing and closing the node".

3. Note the settings of the address selector switch and the

DIL switch elements.

4. Set address 99 and DIL switch elements 1...4 to OFF.

5. Switch on the power supplies (pins 1 and 2).

6. Set the desired test routine on the address selector

switches as follows:

Test routine

Address to be set

Parallel

0, 1 or 2

Serial

Fig.5/9: Setting the test routines

7. Start: Set DIL switch elements 1 and 2 to ON.

If faults occur when the test routine is started, the red LED on
the node will flash fast. The procedure must then be re
peated.

Summary of Contents for IFB05-03



























































































































































Search results

Summary of Contents for IFB05-03

Reviews:

Brands by name

Popular brands

Festo IFB05-03, Manual

Search results

Summary of Contents for IFB05-03

Reviews:

Brands by name

Popular brands