Festo CPX-FB38 Electronic Manual Download Page 23

Page: 23 / 120

1. Installation

1−7

Festo P.BE−CPX−FB38−EN en 0804NH

1.2

Settings of the DIL switches on the bus node

To set the CPX bus node, the cover for the DIL switches must
be removed.

Caution

The CPX bus node contains electrostatically sensitive
components.

Therefore, do not touch any contacts.

Observe the handling specifications for electrostatically
sensitive components.

You avoid malfunctions of and damage to the electronics by
doing so.

1.2.1

Removing and fitting the cover over the DIL switches

You need a screwdriver in order to remove or fit the cover.

Please note

Observe the following instructions when removing or
fitting the cover:

Disconnect the power supply before removing the cover.

Make sure that the seal is seated correctly when fitting
the cover.

Tighten the two fastening screws at first by hand and
then with max. 0.4 Nm.

Summary of Contents for CPX-FB38

























































































































Search results

Summary of Contents for CPX-FB38

Reviews:

Brands by name

Popular brands

Festo CPX-FB38, Electronic Manual

Search results

Summary of Contents for CPX-FB38

Reviews:

Brands by name

Popular brands