Apply adhesive primer in a uniform,
uninterrupted bead.
Using an extrusion gun fitted with a triangular
section nozzle, apply a continuous bead
(3)
of
BETASEAL 1812 code 67306000
, starting from
the mid point of the bottom side.
The end of the bead must overlap the beginning
by approximately
20-30 mm
.
Check that there are no bubbles or interruptions in
the bead; if necessary, correct with additional
sealant.
The fitting of the windscreen on the bodyshell must take place with no possibility of delay within 5 minutes
from the application of the adhesive tape.
Hold the windscreen parallel to the mating surface and fit onto the bodyshell.
Press along the entire perimeter of the windscreen and bring the lower edge against the alignment blocks
fitted previously.
Check that the gaps between the A pillars and the windscreen are uniform.
Apply a few strips of adhesive fabric tape
SYROM 90
, starting from the windscreen and fixing to the pillar and
roof.
Wait at least
3 hours
, remove the adhesive tape and remove any sealant residue from the perimeter of the
windscreen with heptane.
Refit the rain/twilight sensor (
F2.12
).
Refit the interior rear view mirror (
E5.09
).
Refit the roof trim panels (
E4.04
).
Refit the underwindscreen shields (
E4.07
).
Page 4 of 4
Windscreen
8/5/2011
https://modiscs.ferrari.it/KnowledgeOnline/index.php?action=mo&link=link::SM_SM_E30...
Summary of Contents for 458 Italia
