4. OPERATION
•
The blade cuts on a continuous downstroke.
•
Slowly feed the workpiece towards the blade,
putting only ligt pressure on it.
•
Type FLZ-275 will give the best result with wood
with a maximum thickness of 85mm.
•
With both hands firmly hold the workpiece down on
the table and feed it towards the blade slowly,
keeping your hands away from the blade.
•
For the best result the blade must be sharp.
•
Select the right blade for the job, depending on the
thickness of the wood and the cut to be made. The
thinner and harder the wood, the finer the teeth of
the blade. Use a fine-tooth blade for cutting sharp
curves.
•
Use the cross guide provided to feed the workpiece
along the blade slowly and in a straight line.
•
The band saw machine is especially suited for cutting
curves, but will also make straight cuts.
•
When cutting, follow the design marked out by
pushing and turning the workpiece evenly.
•
Do not attempt to turn the workpiece without
pushing it,
as this may cause the workpiece to get stuck or the
blade to bend.
MALFUNCTIONS
Below we have listed a few probable causes and
solutions to which you can refer if your band saw
machine does not function properly.
1. The machine does not work when switched
on.
•
No power supply.
Check the cord for breakage.
Check the fuse.
•
Defective switch.
Return the band saw machine to your local Ferm
dealer to have it repaired.
2. The blade does not move with the motor
running.
•
The blade tension knob has not been tightened.
Switch off the motor. Tighten the blade tension knob.
•
The blade has come of one of the pulleys.
Remove the front plate and check.
•
The saw blade has broken.
Replace the blade.
3. The blade does not cut in a straight line.
•
Use a guide.
•
Put light pressure on the workpiece. Make sure the
blade does not bend.
•
The teeth are dull or damaged.
Try a new blade.
•
Adjust the blade guides
See assembly instruction.
4. The blade does not cut or cuts very slowly.
•
The teeth are dull, caused by cutting hard metals or
long use.
Replace the blade. Use a 6-teeth/inch blade for wood
and soft materials. Use a 14-teeth/inch blade for
harder materials. A 14-teeth/inch blade always cuts
slower due to the finer teeth and the slower cutting
performance.
•
The blade was fitted the wrong way round.
Fit the blade correct.
5. Sawdust builds up inside the machine.
•
This is normal.
From time to time clean the machine.
Remove the front plate and remove the sawdust with
a vacuum cleaner.
6. Sawdust inside the housing.
•
Clean the ventilating slots of the motor with a
vacuum cleaner.
•
Keep the work area clean. From time to time remove
sawdust to prevent it from being sucked into the
housing.
7. The saw-band machines does not cut at 45° or
90° angles.
•
The table is not at right angles to the blade.
Adjust the table.
•
The blade is dull or you put too much pressure on the
workpiece.
Replace the blade or put less pressure on the blade.
8. The blade cannot be properly positioned on
the pulleys.
•
The pulleys are not in alignment. Defective bearing.
Return the machine to your local Ferm dealer to have
it repaired.
•
The pulley alignment knob has not been properly
adjusted.
Adjust the knob (see instructions).
•
Inferior blade.
Replace the blade.
HAVE ALL REPAIRS CARRIED OUT BY AN
AUTHORIZED DEALER OR SERVICE CENTRE! IF
NECESSARY CONTACT YOUR DEALER!
Ferm
7
VEDLIGEHOLDELSE
Træk altid stikket ud af stikkontakten ved
vedligeholdelse og rengøring. Brug aldrig vand eller
andre væsker til at rengøre båndsavmaskinen med. Rengør i
stedet maskinen med en børste.
VED REGELMÆSSIG VEDLIGEHOLDELSE AF
BÅNDSAVMASKINEN UNDGÅS UNØDVENDIGE
PROBLEMER.
•
Hold savbordet rent, således at der under savning
ikke opstår unøjagtigheder ved føringen af
arbejdsemner.
•
Sørg for, at båndsavmaskinens ydre er ren, således at
alle bevægelige dele kan bevæges som de skal og uden
slitage.
•
Sørg for at holde motoren ventilationsåbninger fri
for snavs for at undgå overophedning af motoren.
•
Sørg også for, at maskinens indvendige dele (i nærhed
af savbåndet e.l.) er rene.
Ferm maskiner er blevet konstrueret, så de kan arbejde i
længere perioder med et minimum af vedligeholdelse.
Korrekt vedligeholdelse og rengøring af maskinen er en
forudsætning for lang tids tilfredsstillende brug.
Rengøring
Ventilationsrillerne på maskinen skal holdes rene, så
man undgår overophedning af motoren.
Kappen omkring motoren skal rengøres med en blød
klud, helst hver gang maskinen har været brugt.
Ventilationsrillerne skal holdes fri for støv og snavs.
Hvis snavset ikke vil gå af, bruges en blød klud vredet op i
sæbevand. Der må ikke bruges opløsningsmidler som
f.eks. benzin, sprit, salmiakspiritus o.l. Sådanne
opløsningsmidler kan beskadige dele af plastic.
Smøring
Maskinen skal ikke smøres.
FEJL
Hvis der indtræffer en fejl, f.eks. hvis en del er slidt (op),
kan man kontakte den lokale Ferm forhandler.
Bagest i denne brugsanvisning er der et sprængbillede
med dele, der kan bestilles.
MILJØ
For at undgå at maskinen beskadiges under transport,
leveres den i en solid emballage. De fleste af
emballagematerialerne kan recirkuleres. Disse
materialer kan bringes til den lokale genbrugsplads.
Kasserede maskiner kan afleveres hos den lokale Ferm
forhandler. Her bortskaffes de på en miljøvenlig måde.
GARANTI
Garantibetingelser er beskrevet på det separat vedlagte
garantibevis.
Vi erklærer herved, udelukkende på eget ansvar, at dette
produkt opfylder følgende standarder eller
standardiserede dokumenter
EN61029-1, prEN61029-2-5
EN55014-1, EN61000-3-2, EN61000-3-3,
EN55014-2
i henhold til følgende direktiver:
98/37/EEC
73/23/EEC
89/336/EEC
01-03-2004
ZWOLLE NL
W. Kamphof
Quality department
CE
ı
KONFORMITETSERKLÆRING
(DK)
62
Ferm
