Feel Good mr.steam iTEMPO Installation, Operation & Maintenance Manual Download Page 2

General Information

As you follow these instructions, you
will notice warning and caution 
symbols. This blocked information is
important for the safe and efficient 
installation and operation of this 
control. These are types of potential
hazards that may occur during 
installation and operation:

states a hazard 

may cause serious injury or death 
if  precautions are not followed.

signals a situation

where minor injury or product 
damage may occur if you do not 
follow instructions.

IMPORTANT NOTE: 

This highlights information that is 
especially relevant to a problem-free
installation.

WARNING

!

Table of Contents:

General Information.........................................1

Before Installing ............................................1-2

Dimensional Information..................................3

Installations ...................................................4-7

Installing the Remote 

Temperature Probe ...................................8-10

iTempo Operating Instruction...................11-12

iTempo/Plus Operating Instruction...........13-16

Care and Maintenance...................................17

Warranty.........................................................17

CAUTION

!

mr

.

steam

®

Sussman-Automatic Corporation

®

[email protected] I www.mrsteam.com

43-20 34th Street, Long Island City, NY 11101

9410 S. La Cienega Blvd. Inglewood CA 90301 

1 800 76 STEAM   

FAX

: 718 472 3256

1 800 72 STEAM  

FAX

: 310 216 2944

Summary of Contents for mr.steam iTEMPO





















Reviews: