background image

5

Warning

Warning

1

48      88    90         89         91

OPERATION I INFORMATION FOR THE USER OF THE UNIT

2.1 Start of Sunbathing

Observe the time chart. Do not exceed the sunbathing time recommended for your skin type. You

must definitely avoid sunburn. Never sunbathe if you already have sunburn. Depending on the type

of skin there is a certain final bronzing to be achieved. This bronzing can not be rein force furthermo-

re by using a solarium, but only maintained. When sunbathing, use the protective goggles. Person

whohave had operations on their eye lenses must wear protective goggles. The sunbathing period

can at any time be interrupted with the red EMERGENCY-OFF (NOT-AUS) button of the slot machine

and with the red STOP-button (89) of the unit.

Insert coins or tokens. The initial delay period starts. The unit switches itself on automatically.

2.2 Important Technical Details

Important information! You must read this!

Climate desired (91, seesaw-button on the operating panel)

Here you determine how much cooling air will be blown on the body.

Ventilator

The ventilator in the tripod still goes on 4 minutes after switching off the unit, in order to cool down the unit.

Lighting effect

Behind the small covering hood (57) standing beside the feet, there is a permanent shining source of light.

BreakSafe

The XTT filter discs of the lounger and the XTT filter discs of the tanning arms are equipped with a BreakSafe

protection. That is to say, whenever a filter disc breaks or whenever you forgot to put in a filter disc when

exchanging the burner, the electrical circuit will be interrupted and the unit can not be started 

(

see Section

8 BreakSafe).

Speakers (34, picture 3)

There are two speakers so that you can enjoy the music played on the central sound system while you tan

(See picture 2 number 12).

2.3 Inside area of the tanning unit

Lie down on the lounger.
While sunbathing, keep your arms near your body on the lounger.

If the lights are still off, the initial delay period is active. The lights automatically switch on after the end of the initial

delay period. The interval of tanning is determined by the construction of the unit. Now you can reach the operating

panel (48, picture 1) comfortably with the right hand.

START/STOP-button, LED-display (picture 1)

As soon as the lights switched on, the 2-figured LED-display (88) is counting up the time in minutes. Here you can

read the sunbathing time that you have spent. After the end of the sunbathing time the unit switches off and the

display shows 0. While sunbathing, you can interrupt the sunbath with the red STOP-button (89) and with the green

START-button (90, starts again after approx. 4 minutes) you can start again. The sunbathing time keeps going on

during this interruption, that is to say, the display goes on counting.

Seesaw button ventilator (91)

With the seesaw-button (91) you choose the desired climate for sunbathing. The cooling air will be carried over

the body out of the jet (92, picture 3) and out of the ventilation slots (92). On the positioning of the seesaw

button depends the power of the supply of cooling air.

Middle position

Supply of cooling air OFF

Symbol

Supply of cooling air medium power

Symbol

Supply of cooling air full power

Summary of Contents for SunBoard XTT





















Reviews: