FarmTek FodderPro 2.0 Instructions Manual Download

Page: 4 / 53

111628E

Revision date: 02.16.23

Connecting Multiple Systems to a 2" Main Supply Line

Except for the additional 2" PVC pipe shown in the diagram, each system includes the following components to connect to a 2" main water supply line:

•

(1) WF1386 (PVC 2" Tee)

•

(2) WF3516 (2" Ball Valve)

•

(1) WF2391 (2" x 3/4" Bushing)

ATTENTION: WHEN CONNECTION TWO (2) OR MORE FODDER SYSTEMS TO THE SAME MAIN

SUPPLY LINE, YOU MUST CONNECT THE LINE TO THE TOP OF EACH SUPPLY MANIFOLD.

RECOMMENDED SPACING

For easy maintenance and access, maintain

at least 48" between fodder frames.

WF1386

WF3516

2" PVC Pipe

(Additional Purchase Required)

WF3311

(3/4" Ball

Valve)

Included

with Fodder

System

2" PVC Pipe

WF2391 (2" x 3/4")

Summary of Contents for FodderPro 2.0






















































Search results

Summary of Contents for FodderPro 2.0

Reviews:

Related manuals for FodderPro 2.0

Brands by name

Popular brands

FarmTek FodderPro 2.0, Instructions Manual

Search results

Summary of Contents for FodderPro 2.0

Reviews:

Related manuals for FodderPro 2.0

Brands by name

Popular brands