Farmet EXCELENT PREMIUM 6 Instructions For Use Manual Download

Page: 42 / 52

Manual

EXCELENT Premium 6; 8

│

7.1.4

Adjusting the Harrowing

The height setting of harrowing is performed with the use of the handle. The angle setting is executed by the pin.
Its position is changed in the holes of the setting plate.

Picture 61 – Setting the harrowing

7.2.

SHARE PROTECTION



The basic setting of the supporting spring is set by the producer to

184 ± 2 mm

so that it is

horizontal.



Check regularly that the nuts of the bottom and upper stopper are tight, if not, tighten them.



Check regularly that the nuts of the supporting screw inside the spring are tight.

Picture 62 – Share protection

Handle for setting

the height

Pin for setting

the slope

Standardly set to

184 ± 2 mm

Upper stopper

Bottom stopper

Protection screw

Protection nut

Summary of Contents for EXCELENT PREMIUM 6





















































Search results

Summary of Contents for EXCELENT PREMIUM 6

Reviews:

Related manuals for EXCELENT PREMIUM 6

Brands by name

Popular brands

Farmet EXCELENT PREMIUM 6, Instructions For Use Manual

Search results

Summary of Contents for EXCELENT PREMIUM 6

Reviews:

Related manuals for EXCELENT PREMIUM 6

Brands by name

Popular brands