Farmet EXCELENT PREMIUM 6 Instructions For Use Manual Download

Page: 47 / 52

Manual

EXCELENT Premium 6; 8

│

Picture 69 – Roll bearings

Picture 70 – Roll bearings

Picture 71 – Bearings of axle

Picture 72 – Handle for setting the harrowing

MANIPULATION WITH LUBRICANTS:



Handle lubricants and oils as hazardous waste according to the valid acts and regulations.



Protect yourself from direct contact with oils by using gloves or protective lotion.



Wash oil stains on skin thoroughly with warm water and soap. Do not clean the skin with petrol, diesel oil or
other dissolving agents.



Oil is poisonous. If you swallow any, immediately seek a doctor.



Keep lubricants out of reach of children.

RECOMMENDED TIGHTENING MOMENTS OF BOLTING

BOLTING

TIGHTENING

MOMENT

NOTE

M8x1

8Nm

Fastening screws of house bearings

M8 (8.8)

25Nm

M10 (12.9)

85Nm

Share screws

M12 (8.8)

87Nm

House bearings

M16 (8.8)

210Nm

Rubber-tyred roller wheels

M 20 (8.8)

50Nm

Rotary harrowing screws

M20 (8.8)

410Nm

Protection screws, axle rubber-tyred roller wheels

M24 (8.8)

710Nm

Hopper screws

HYD AIR JOINTS

M16x1,5

60Nm

Hydraulic screwing, air screwing

M22x1,5

140Nm

Hydraulic screwing, air screwing

Summary of Contents for EXCELENT PREMIUM 6





















































Search results

Summary of Contents for EXCELENT PREMIUM 6

Reviews:

Related manuals for EXCELENT PREMIUM 6

Brands by name

Popular brands

Farmet EXCELENT PREMIUM 6, Instructions For Use Manual

Search results

Summary of Contents for EXCELENT PREMIUM 6

Reviews:

Related manuals for EXCELENT PREMIUM 6

Brands by name

Popular brands