Farmet 2021/0625 Operating Instruction Download

Page: 66 / 102

17.1.1

Recommended depth

The setting of the sowing depth and the coulter pressure interact.

After each sowing depth change, drive a few meters and check the seed placement depth and the
coulter pressure.

Species

Recommended

sowing depth

Recommended

sowing rate

Spring wheat

4-5 cm

220 kg

Spring triticale

4 cm

200 kg

Spring barley

3-5 cm

200 kg

Oat

3-5 cm

200 kg

Corn

5-8 cm

20-70 kg

Buckwheat

3-5 cm

70 kg

Peas

4-6 cm

250-300 kg

Spring weasel

4-6 cm

120-180 kg

Broad bean

6 cm

180-250 kg

White lupine

6-8 cm

160-180 kg

Spring rape

2-3 cm

3-6 kg

White mustard

2-3 cm

8-10 kg

Poppy seeds

1-2 cm

1 kg

Sunflower

4-6 cm

4-25 kg

Meadow clover

1-2 cm

15-20 kg

Lucerne

1-2 cm

8-16 kg

Summary of Contents for 2021/0625







































































































Search results

Summary of Contents for 2021/0625

Reviews:

Related manuals for 2021/0625

Brands by name

Popular brands

Farmet 2021/0625, Operating Instruction

Search results

Summary of Contents for 2021/0625

Reviews:

Related manuals for 2021/0625

Brands by name

Popular brands