Farmet 2021/0625 Operating Instruction Download

Page: 93 / 102

Alarm text

Possible cause

Possible remedy

667

Sensor error detected
PLANTirium®. LIN-BUS
communication error.

AQ LIN-Bus communication error has
occurred. The sensor did not receive
any messages from the LIN-Bus.

Check the cables.

668

Working speed is out of speed
range.

Working speed is too high or too low.

Make sure you are within the speed
range you found during the
calibration test.

669

An error has been detected in the
PLANTirium® sensor. Connection
lost.

The connection to the

PLANTirium®

sensor has been disconnected.

Check the cables on the sensor.

670

Seed flow system error. Error:
Sensor:

An error has occurred in the seed flow
system.

Check the seed flow system.

671

Seed flow system error.

An error occurred in the seed flow
system.

Check the seed flow system.

672

Product flow detected in inactive
row.

Product flow detected in inactive row. Check disconnection.

680

Connection lost.

The connection to the
monitoring/control module has been
disconnected.

Check cables.

681

Undefined module index.

An unconfigured monitoring/control
module was found.

Check the number of configured or
connected modules.

685

An error been detected in the
control module.

Voltage drop, module error.

It is necessary to perform diagnostics
and possible replacement of the
module.

686

Supply voltage too low.

The supply voltage at the
monitoring/control module is too low.

Check the cables.

688

The target value cannot be met.
Seed coulter pressure.

The required setpoint for the linear
actuator has not been reached.

Check the linear actuator for
blockage.

689

The target value cannot be met.
Working depth.

The required setpoint for the linear
actuator has not been reached.

Check the linear actuator for
blockage.

690

An error has been detected in the
CAN repeater. 5V

– Wrong voltage.

The CAN repeater is defective.

Contact customer service.

691

An error has been detected in the
CAN repeater. 3.3 V

– Wrong

voltage.

The CAN-Defeater is defective.

Contact the customer service.

692

An error has been detected in the
CAN repeater. 2.5 V

– Wrong

voltage.

The CAN-Defeater is defective.

Contact customer service.

693

Error detected in CAN-Repeater 12
VE- Faulty voltage.

The power supply to the electronics is
defective.

Check the cables.

Summary of Contents for 2021/0625







































































































Search results

Summary of Contents for 2021/0625

Reviews:

Related manuals for 2021/0625

Brands by name

Popular brands

Farmet 2021/0625, Operating Instruction

Search results

Summary of Contents for 2021/0625

Reviews:

Related manuals for 2021/0625

Brands by name

Popular brands