Farm King 1460 Operator And Parts Manual Download Page 33

Page: 33 / 168

Assembly - Fertilizer Applicator 1460

Coulter Knife Alignment

NOTE: The following images may not show your

exact coulter assembly as it appears but the
procedure is correct.

Figure 8

Knives should rub slightly on blade at bottom of knife
(CORRECT)

[Figure 8]

Figure 9

Loosen the two bolts (Item 1)

[Figure 9]

and adjust knife

to rub slightly on blade. Tighten bolts.

Orifice Installation (Coulters / Knives)

Figure 10

Loosen hose fitting by 1/4 turn (Item 1)

[Figure 10]

and

disconnect.

Install orifice between hose fitting and diaphragm check
valve, for the desired application rate and travel speed.

Connect and tighten hose fitting by 1/4 turn back on to
the check valve.

Tip Installation (Coulters / Injectors)

Figure 11

Install spray tip, I.E. TeeJet StreamJet tip into female
threads located at the bottom of the assembly (Item 1)

[Figure 11]

B-0175

B-0174

CORRECT

WRONG

B-0179

B-0559

Summary of Contents for 1460









































































































































































Search results

Summary of Contents for 1460

Reviews:

Related manuals for 1460

Brands by name

Popular brands

Farm King 1460, Operator And Parts Manual

Search results

Summary of Contents for 1460

Reviews:

Related manuals for 1460

Brands by name

Popular brands