Farfisa KM8262CW User Manual Download

Page: 5 / 20

Mi 2334/1

- 5 -

Using the push-button keyboard for
programming

Press button "

" and " " to enter addresses

or codes.

:Press this button to

access the

programming mode

(when pressed for 4

seconds with off-hook handset),

confirm

address or code programming

go to

the next programming step.

Press this button to

increase the value

you want to enter.

Press the button for a

number of times equal to the digit you want
to enter (digit 1 = 1 time; digit 9 = 9 times;
digit 0 = 10 times button “ ”).

Pressure of button “ ” is confirmed by an acoustic
tone.

Entering the programming mode

To enter the programming mode you must:

pick up the handset and leave it off-hook
during the entire programming step;
press button “

” for at least 4 seconds until

you receive the confirmation tone.

Entering codes or addresses

- Codes and/or addresses must have three

digits  (hundreds,  tens,  units);  codes  and/or
addresses  with  tens  and  units  or  units  only
must  be  completed  by  adding  zeros.  For
example,  address  96  will  become  096  and
address 5 will become 005.

- Digits must be entered individually, by

pressing the button “ ” for a number of times
“n”, where “n” is the value of the digit you want
to enter, followed by a pause of about 2 seconds
before you go to the next digit (a tone in the
handset will tell you when to go to the next
digit).
For example, to enter code 096 you must:
- press button “ ” 10 times to enter digit 0, wait
for 2 seconds until you hear a sound in the
handset.
- press button “ ” 9 times to enter digit 9, wait
for 2 seconds until you hear a sound in the
handset.
- press button “ ” 6 times to enter digit 6, wait
for 2 seconds until you hear a sound in the
handset.
- press button “

” to confirm entering and go

to the next programming step. An acoustic
tone in the handset will confirm that the code
has been stored and you can go to the next
step.

Exiting the programming mode

You will automatically exit the programming
mode after pressing button "

" to confirm the

7th programming, i.e. “

code to assign to button

“ ”. You can also exit the programming mode at
any time by hanging up the handset. Settings
will not be saved if you exit the programming
mode without confirming with button "

You  will  also  exit  the  programming  mode
automatically  if  you  make  a  mistake  or  an
operation that is not permitted when entering a
code.  In  this  case,  you  must  access  the
programming mode again to continue.

Automatic programming

You can use the automatic programming mode
to save the intercom address from the external
station.

Automatic programming procedure

To enter the automatic programming mode you
must:

a) enter the programming mode

following the

instructions described in “Entering the
programming mode

”;

b) make a call from an external station within

2 minutes

. In case of installations with digital

push-button keyboard TD2100MA, key in
the number you want to assign to the intercom
and press “

”. In case of installations with

digital  encoder  CD2132MA  or  CD2134MA
press the button you want to assign to the
user on the push-button keyboard. When the
call  is  received,  the  videointercom  is
programmed automatically, you hear the call
tone in the handset and the videointercom is
turned on, showing the calling external station.
Close  and  pick  up  the  handset  to  start  a
conversation  with  the  external  station  and
check the correct operation of the system;

c) at the end of the conversation hang up the

handset

to exit the automatic programming

mode.

Simplified programming

The simplified programming mode allows for
quick saving of the videointercom address.

Simplified programming procedure

To enter the simplified programming mode you
must:

a) enter the programming mode

following the

instructions described in “Entering the
programming mode

”;

b) enter the three digits of the user address.

Digits must be entered individually, by
pressing the button “ ” for a number of times
“n”, where “n” is the value of the digit you want
to enter, followed by a pause of about 2
seconds before you go to the next digit (a
sound in the handset will tell you when to go
to the next digit).
For example, to enter code 096 you need to:
- press button “ ” 10 times to enter digit 0, wait
for 2 seconds until you hear a sound in the
handset.
- press button “ ” 9 times to enter digit 9, wait
for 2 seconds until you hear a sound in the
handset.
- press button “ ” 6 times to enter digit 6, wait
for 2 seconds until you hear a sound in the
handset.

c) hang up the handset

as soon as you hear

the confirmation tone in the handset to exit
the simplified programming mode.

Manual programming

The manual programming mode allows you to
enter the user address, assign the internal
address and codes to buttons " " and “ ”

Manual programming procedure

To enter the manual programming mode you
must:

a) enter the programming mode

following the

instructions described in “Entering the
programming mode

”;

b) programme the following functions in

sequence:

User address

– this code allows you to

receive  an  external  call,  turn  on  the
videointercom,  have  a  conversation  and
open the door at the calling external station.
For  information  on  address  entering  see

“Entering codes or addresses”

Internal address

– these codes are used

to identify the videointercoms installed in
the  apartment  (max.  3).  In  case  of  one
videointercom only, the internal code must
be  000  (default  value);  if  other  video-
intercoms are present (max. other 2) you
must assign codes 001 and 002 to them.
By entering these codes, all videointercoms
will ring when an intercom call is made; if
you prefer not to activate the intercom ring
in the third videointercom, you must assign
code 003 instead of 002.
For  information  on  code  entering  see

“Entering codes or addresses”

Address of external station 1 associated

with button

" " – address of external

station  1  you  want  to  connect  with  when
button  " "  is  pressed.  If  the  installation
only  includes  one  external  station,  the
address does not need to be stored, since
it will be automatically acquired upon the
first call.

Address of external station 2 associated

with button

" " – address of external

station 2 you want to connect with when
button " " is pressed. This code does not
need to be saved if the installation does not
include two external stations.
For information on code entering see

“Entering codes or addresses”

Address of external station 3 associated

with button

" " – address of external

station 3 you want to connect with when
button " " is pressed. This code does not
need to be saved if the installation does not
include three external stations.
For information on code entering see

“Entering codes or addresses”

Address of external station 4 associated

with button

" " – address of external

station 4 you want to connect with when
button " " is pressed. This code does not
need to be saved if the installation does not
include four external stations.
For information on code entering see

“Entering codes or addresses”

Address associated with button

“ ”

– to

call users from other apartments you must
enter their user address (001 to 200). Enter
code 000 if you want to use this button to
make intercom calls between intercoms in
the same apartment.
For information on code entering see

“Entering codes or addresses”

“Manual programming”

mode the 7 steps

above must be performed in sequence from
step 1 to step 7. Each step must be confirmed
by pressing button “

”. Press button “

”

again if you want to skip a programming
operation and go to the next one. For example,
after you have programmed the “

user

address

(step 1)” and confirmed it by pressing

button “

”, you will automatically go to the