manualshive.com logo in svg

fann 102538946, Instruction Manual, Page: 15 / 48

Share
Download
fann 102538946 Instruction Manual Download Page 15

 

Model 415C & 415 SGS Instruction Manual

 

D01669102 

April 2019, Revision A 

15  

6 

Using the Touchscreen Software 

6.1  What is a touch screen and how does it work? 

Touch screens were created to provide users with an easy to use interface. This 
allows the user to input and view data without a keyboard or mouse. The touch 
surface is able to detect contact and send position information back to the 
processor. Using the touch screen has the same result of using a mouse to point and 
click. One mouse click is accomplished by one touch of the screen. A double-click 
is achieved with two quick touches.  With this standard method of input, no special 
software is required to utilize the screen. 

6.2  Using the Touch Screen 

A finger or stylus is most often used on the touch-screen.  Experimentation will 
quickly show which objects will activate the screen and which will not.  It is 
important to note the touch surface does NOT use pressure to detect input. A light 
touch is all that is needed.  In addition sharp instruments (such as pencils, pens, 
screwdrivers, etc.) should not be used as they may damage the touch surface. A 
pen-like touch stylus has been included in your accessories to use if desired. 

6.3  What can you do with the touch screen software? 

The purpose of the touch screen is to provide the user with a single interface to the 
instrument.  All instrument operations are accessed and controlled through the 
touch screen. This consistometer is a leap forward in design because it is the first 
time that mechanical control has been eliminated from the point of view of the 
operating technician. Filling and draining the pressure vessel with oil, heating and 
cooling, pressurizing and depressurizing, and rotational speed are all fully 
automated. Our unique testing and test data screens offer detailed control over test 
parameters and the way your plot looks including color designations and job 
properties. Alternately, test data can be exported raw and utilized however one 
wishes. Each instrument is complete and requires no additional software or 
hardware to function. 

6.4  One Key Recovery for the Computer 

Instruments manufactured after March 2014 have computer systems which have 
One Key Recovery factory restoration points. What this means is that if the 
computer has a severe virus attack, operating system crash, hard disk failure or 
corrupted programs and software then the user may take simple steps to restore the 
system to its original factory condition. Simply pressing F3 during the 10 second 
boot sequence brings up access to the recovery menu. Select option 1 for a factory 
restore. Original application programs and configurations will be restored. 
Alternately, a newer backup point can be created. For example if you have updated 
the CementLab software to a newer version, performed new calibrations, and have 

Summary of Contents for 102538946

















































Reviews:

No comments