FALK QUADRIVE JF Manual Download Page 35 | Manualshive

Page: 35 / 52

background image

Motor Mount Installation

Introduction

The Falk Equi-Poised Motor Mount is an all-steel weldment that
bolts directly to the steel frame of Falk Shaft Mounted (Type JR),
Flange Mounted (Type JF) and Screw Conveyor (Type JSC)
Drives, as shown in Figure 1.

This modern design provides a simple means of tensioning
V-belts with adjusting screws. The motor base plate is
pre-drilled for rerated NEMA standard foot-mounted motors
within the rated capacity of the drive.

Assembly Instructions

From Figure 2, determine which assembly is required. Drives
are shown assembled in the 3 o’clock position, high speed
shaft relative to low speed shaft. They can also be mounted in
the 6, 9 and 12 o’clock positions after the motor mounts are
assembled.

WARNING

:

Remove all external loads from drive before

servicing drive or accessories.

Consult applicable local and national safety codes for proper
guarding of rotating members.

1. Assemble motor mount bracket to drive.

a) Sizes 4407 thru 4507 — Remove housing cover fasteners

and bolt motor mount bracket to housing using longer
fasteners provided.

b) Size 4608 — Attach bracket to pads provided on seal

cage.

2. Assemble rear support bracket to drive.

a) Sizes 4407 thru 4507JR and 4407JF, JSC (Figure 3) —

Remove nuts and lock washers from seal cage studs and
attach rear support bracket.

b) Sizes 4415, 4507 and 4608JF (Figure 4) — Attach rear

support to flange using mounting bolts furnished by user
(Furnished by Falk for Size 4608JF).

c) Size 4608JR (Figure 3) — Attach rear support bracket to

seal cage pads using fasteners provided.

The Falk Corporation, P.O. Box 492, Zip 53201-0492

378-102

3001 W. Canal St., Zip 53208-4200, Milwaukee, WI USA Telephone : 414-342-3131

August 2004

Fax: 414-937-4359 e-mail: [email protected] web: www.falkcorp.com

Supersedes 6-92

®

a good name in industry

Quadrive Shaft Mounted Drives

•

Appendix D

Sizes 4407/M4407-4608/M4608

(Page 35 of 52)

ADJUSTING

SCREW

REAR

SUPPORT BRACKET

MOTOR MOUNT

MOTOR

BASE PLATE

JAM NUT

Figure 1

OSHA type guard
when specified.
Dimensions
to suit
components.

A3

(3 o’clock)

C3

(3 o’clock)

D3

(3 o’clock)

Letter = Motor Mount Position, Clock = Drive H.S.S. Position

STANDARD ASSEMBLIES

Figure 2

SEAL CAGE

STUD

NUTS

REAR

SUPPORT

BRACKET

FASTENERS

FLAT WASHERS

LOCK WASHERS

NUT

Figure 3 Sizes:
4407 thru 4507JR
4407JF & JSC
4608JR

FASTENERS

FLAT WASHERS

LOCK WASHERS

REAR

SUPPORT

BRACKET

FLANGE

LOCK WASHERS

MOUNTIN

BOLT

NUTS

Figure 4 Sizes:
4415 thru
4608JF

«
...
33
34
35
36
37
...
»

Summary of Contents for QUADRIVE JF





















































Reviews:

No comments

Related manuals for QUADRIVE JF

Brand: Navman Pages: 17

Brand: Datalogic Pages: 20

Brand: Datalogic Pages: 188

Brand: Water Witch Pages: 2

Brand: Falltech Pages: 48

PORTABLE ICE FISHING KIT

Brand: Garmin Pages: 5

Brand: Landi Renzo Pages: 16

Brand: IBM Pages: 163

Brand: Oakworks Medical Pages: 28

Brand: MagCore Pages: 80

Brand: MagCore Pages: 80

APT-9411 Series

Brand: TAKAYA Pages: 77

Brand: Tadano Pages: 402

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

IMPULSE 2 IT8026 Glute Master

Brand: BM FITNESS Pages: 18

Brand: Kobelt Pages: 20

Brand: Pottinger Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands