FALK QUADRIVE JF Manual Download Page 50

Page: 50 / 52

WARNING:

Consult applicable local and national safety

codes for proper guarding of rotating members.

WARNING:

Lock out power source and remove all external

loads from drive before servicing drive or accessories.

The Falk Corporation, P.O. Box 492, Zip 53201-0492

378-102

3001 W. Canal St., Zip 53208-4200, Milwaukee, WI USA Telephone: 414-342-3131

August 2004

Fax: 414-937-4359 e-mail: [email protected] web: www.falkcorp.com

Supersedes 6-92

a good name in industry

Appendix M

•

Quadrive Shaft Mounted Drives

(Page 50 of 52)

Sizes 4407/M4407-4608/M4608

OSHA V-Belt Guard Installation For Drives With Shaft Fan

1. ASSEMBLE MOTOR MOUNT AND MOTOR TO DRIVE AS
INSTRUCTED IN APPENDIX D

4. ASSEMBLE THREADED RODS TO BACKPLATE & MOUNT
SLOT COVER(S) AS REQUIRED

2. ASSEMBLE GUARD MOUNTING BRACKET & ADAPTER TO
GUARD BACKPLATE

5. MOUNT BELT DRIVE AS INSTRUCTED IN APPENDIX D

3. ASSEMBLE BACKPLATE WITH ADAPTER TO SHROUD

6. MOUNT COVER

ALLOW FOR BELT

INSTALLATION

ALLOW FOR

BELT TAKE UP

LOCKNUT

& FLAT

WASHER

CH_930001

Exposed

moving

parts

can cause

severe

injury

LOCK

OUT

POWER

before

removing

guard

WARNIN

GUARD

BACKPLATE

SLOTS

LOCKNUT

HEXNUT

A9 MOTOR MOUNT
POSITION

Summary of Contents for QUADRIVE JF





















































Search results

Summary of Contents for QUADRIVE JF

Reviews:

Related manuals for QUADRIVE JF

Brands by name

Popular brands

FALK QUADRIVE JF, Manual

Search results

Summary of Contents for QUADRIVE JF

Reviews:

Related manuals for QUADRIVE JF

Brands by name

Popular brands