FALK QUADRIVE JF Manual Download Page 36 | Manualshive

Page: 36 / 52

background image

Motor Mount Installation

3. Assemble support bracket to motor mount bracket — Use

the fasteners provided. Torque all fasteners to values listed in
Table 1.

4. Assemble base plate to motor mount bracket — Assemble

adjusting screws to motor mount bracket and base plate with
jam nuts above and below the base plate.

5. Mount motor — Position motor on base plate so that all

mount holes are in alignment. Install and tighten motor
fasteners.

6. Mount sheaves and V-belt — Mount sheaves as close to the

drive and motor housing as possible. Hold a straight edge
across the faces of the two sheaves to obtain correct
alignment. Adjust V-belt to the tension recommended by the
belt manufacturer by turning the adjusting screws evenly.
When the required tension is reached, tighten lock nuts. DO
NOT over tighten belts. Over tightening belts reduces belt
and bearing life.

The Falk Corporation, P.O. Box 492, Zip 53201-0492

378-102

3001 W. Canal St., Zip 53208-4200, Milwaukee, WI USA Telephone: 414-342-3131

August 2004

Fax: 414-937-4359 e-mail: [email protected] web: www.falkcorp.com

Supersedes 6-92

®

a good name in industry

Appendix D

•

Quadrive Shaft Mounted Drives

(Page 36 of 52)

Sizes 4407/M4407-4608/M4608

TABLE 1 — Fastener Size and Tightening Torque lb-in (Nm)

H

DRIVE

SIZE

Motor Mount

to Housing

Support to

Seal Cage

Support to Motor Mount

Support to

Flange

Size

Torque

Size

Torque

Size

Torque

Size

Torque

4407

.500-13

825 (93)

.750-10

3960 (447)

.500-13

825 (93)

.750-10

3960 (447)

4415

.500-13

825 (93)

.750-10

3960 (447)

.500-13

825 (93)

1.25-7

12600 (1 424)

4507

.500-13

825 (93)

.875-10

6400 (723)

.500-13

825 (93)

1.25-7

12600 (1 424)

4608

.500-10

2940 (332)

.750-10

2940 (332)

.500-10

2940 (332)

.750-10

2940 (332)

H

All fasteners are Grade 5.

«
...
34
35
36
37
38
...
»

Summary of Contents for QUADRIVE JF





















































Reviews:

No comments

Related manuals for QUADRIVE JF

Brand: Eclipse Combustion Pages: 46

Brand: Bard Pages: 2

Brand: idiag Pages: 12

Brand: BACtrack Pages: 13

Brand: Badgematic Pages: 28

Brand: BACtrack Pages: 2

Brand: MADRIX Pages: 28

Brand: BACTcontrol Pages: 28

Brand: Major Pages: 52

Brand: H&S Pages: 42

Brand: OHAUS Pages: 84

Brand: Hach Pages: 456

Brand: Zimmer Pages: 2

Brand: ZipRip Pages: 31

Brand: Garrick Pages: 8

SpinVessel 650ml

Brand: V&P Scientific Pages: 9

LED Studio 3300D

Brand: PR Lighting Pages: 16

Brand: Old Town Canoe Co. Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands