page 13
BIRIO LC DEVICE OPERATING
The Birio LC device has a practical and intuitive use, it does not allow the codification between the Radio Receiver and the Transmitter, but it can copy,
replace and delete both clear and key-encoded transmitters (provided that the keys were encoded by the same Birio Lc Device); and copy either blank
or key-encoded Memories(provided that the keys were encoded by the same Birio Lc Device).
Leds lighting on the Device will help during the operations. Every operation is carried out simply by pushing the corresponding button on the Device.
To return from mode Transmitter to mode Memory and viceversa simply turn off and turn on the Device. Remember that when the Device is turned
off all received information is cancelled. Therefore after turning the Device on and starting with the new operations it is necessary to send the
information to the Birio LC Device of the transmitter and the memory you need to operate in.
TRANSMITTER:
As soon as the Birio LC Device is switched on, it is in mode Transmitter; if the corresponding buttons are pushed all information about the key-codes and
the family of the Device will be displayed.
A Birio LC Device can read the data of a transmitter which was key-encoded by a Birio LC Device belonging to a different family. In this case the presence
of the key and and the type of Device that encoded the transmitter are displayed. If the message Error is displayed it means that the Birio LC Device did
not read the transmitter information and thus no operation can be carried out.
MEMORY: After switching on the Birio LC Device, push the Memory button (the first button on the left) and you enter Memory mode: all information about
the key-codes and the family of the Device will be displayed.
A Birio LC encoding Device can read the data of a Memory which was key-encoded by a Birio LC Device belonging to a different family. In this case the
presence of the key and and the type of Device that encoded the Memory are displayed.
If the message Error is displayed it means that the Birio LC Device did not read the Memory information and thus no operation can be carried out.
"BIRIO TOOL" PC SOFTWARE: The Birio LC Device can also be used as a support to the PC software for customers' managing. Connect the Birio LC Device
to the PC serial port COM1, then open the software and turn on the Birio LC Device, click on connection and all the information (except the keys) of the
Memory and the Transmitter will be displayed.
Key-encoding must be carried out according to the family of the Birio LC Device.
- The Master Device (for ex. A) encodes clear Transmitters and Memories with the 1st key C1
- The Slave Device (for ex. A1, A2,...) encodes only the 2nd key (C2) into those Transmitters and Memories which were 1st-key encoded by the Master
Device belonging to the same family
If an "Error" message is displayed it means that the operation was not correctly carried out, or that the transmitter was key-encoded by
a Birio device belonging to a different family.
2°
Push the button
Enter Key
: "T- Enter Key" will be displayed, followed
by "Enter Transmitter"
IMPORTANT:
when the operation is completed, check the transmitter information by following the operation "transmitter data reading"
on page 14.
page 15
1°
Follow the operation Transmitter data
reading page 14
3°
Position the transmitter onto the Birio LC Device . When the led turns off the
operation is completed.
N.W. If, when the led turns off, another transmitter is positioned, before
TRANSMITTER is displayed, it is possible to encode this second transmitter too.
MEMORIY
ENTER
KEYS
DELETE
KEYS
COPY
REPLACE
DELE
TE
COPY ON
E BUTT
ON
SELECT
CODE
MEMO
RY
Birio
LC
GB
No Key
Transmitter code:
00 20 D9
DISPLAY
Enter transmitter
T - Enter Key
DISPLAY
TRANSMITTER KEY ENCODING
4213
TRANSMITTER
DISPLAY
TRANSMITTER
DISPLAY
REPLACE
DELETE
COPY ONE BUTTON
COPY
MEMORY
ENTER
KEYS
DELETE
KEYS
SELECT
CODE
Siti
Siti
Summary of Contents for Siti 63
Page 1: ...GB I...
Page 2: ...NL F D E...
