26 27 28 29 30
31 32 33 34 35 36
A
B A
B
Capacitor 20 μF
M3
Capacitor 20 μF
M4
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15
16 17 18 19 20 21
A
B A
B
9
Elpro S40
COMMON
OPEN
CLOSE
RADIO
LED 24 V - 3 W max
STOP
T1
MOTOR RUN TIME
1 s - 22 s
T2
DWELL TIME
1 s - 180 s
L1
L6
L7
L3
L8
L4
L5
L2
L9
L10
L11
Secondary
fuse
transformer
F4 = 2A
Primary
fuse
transformer
F3 = 630 mA
Electric valve fuse,
acoustic device, flashing light
and led F5 = 2 A
Motor fuse M2
F2 = 5 A
Motor fuse M1
F1 = 5 A
COMMON
M1
M2
COMMON
Red
Yellow
Green
Input P
57 58
63 64 65 66 60 61
24 Vdc output
+
-
55 56
TRANSFORMER
1 2
COMMON
COMMON
LIMIT SWITCH OPEN M3
(Bollard in down position)
LIMIT SWITCH OPEN M1
(Bollard in down position)
LIMIT SWITCH OPEN M2
(Bollard in down position)
LIMIT SWITCH CLOSE M1
(Bollard in up position)
LIMIT SWITCH CLOSE M2
(Bollard in up position)
Pedestrian opening
connection
motor bollard M1
PHOTOCELLS OR
MAGNETIC LOOP
OUTPUT 24 V - 250 mA
for max charge:
- n° 2 pairs of photocells
- n° 1 radio receiver
LIMIT SWITCH CLOSE M3
(Bollard in up position)
MOTOR M3
Bollard n° 3
MOTOR M4
Bollard n° 4
MOTOR M1
Bollard n° 1
MOTOR M2
Bollard
n° 2
LIMIT SWITCH OPEN M4
(Bollard in down position)
LIMIT SWITCH CLOSE M4
(Bollard in up position)
COMMON
COMMON
NEUTRAL
LIVE
N
F
Anti-disturbance filter
COMMON
Elpro S40
STRIP jumper
LIMIT SWITCH
ELPRO S40
Motor
fuse M4
F6 = 5 A
Motor
fuse M3
F7 = 5 A
L12
L13
L14 L15
M3
M4
3 4
Capacitor 20 μF
M1
20 VA - 50/60 Hz
M3A M3C M4A M4C
23
22
24
25
Capacitor 20 μF
M2
RADIO
PLUG-IN CARD
CONNECTOR
LIMIT SWITCH DIAGNOSTIC
230 V - 50 Hz
POWER SUPPLY
STABILIZER
FOR SOLENOID VALVE
POWER SUPPLY
230 V ±10% 50 Hz
SINGLE-PHASE
Red
FLASHING LIGHT
230
V - 100
W max
SIGNAL LIGHT
230
V - 100
W max
Fuse 1 A
PLUG-IN CONNECTOR FOR
3-LAMP TRAFFIC LIGHTS
MAX100 W EACH LAMP
Y
ello
w
Gr
een
C
ommon
P
o
w
er supply
12
V - 24
V - 230
V
(
Optional:
plug-in PCB for traffic
light to suit 230 V lamp)
code
7282L
Coral, Vigilo, Talos, Talos M30, Strabuc 930 Opinat
range of bollards with limit switch: with the STRIP jumper inserted (as in the picture), Elpro S40
checks cyclicly every 10 minutes that the closing limit switches (post raised) are in the correct position; should any of them fail to be such, only the
motor of the post not in position is operated until this is fully up as required.
Note well:
whenever
Elpro S40
is re-powered, wait 10 seconds for the logic to become fully operating again.
The electronic control panel Elpro S40 is designed to operate the Talos, Talos M30, Strabuc 930 Opinat, Coral and Vigilo; power supply is
230 V single-phase.
Elpro S40 is capable of monitoring damages or malfunctioning with the system (ISC).
I.S.C.
=
I
ntegrity and
S
upervision
C
ircuit, is a special function of Elpro S40 which can self control the electronic PCB and detect any damages
occurring with any components or accessories. In this case, provided that the post is fitted with a release electric valve, lowering is allowed
automatically. The manufacturing company declines any responsability for incorrect handling and application; also, it reserves the right to
change or update the control panel any time.
IMPORTANT FOR THE INSTALLATION AND THE CORRECT FUNCTIONING:
- The control box must be installed in a dry and sheltered place.
- Make sure that power supply to the control board be 230 V ±10%.
- Make sure that power supply to the electric motor be 230 V ±10%.
- For distances longer than 50 metres increase the section of the wires.
- Fit the mains to the control box with a high sensitivity, 0,03 A, differential, magnetic-thermal circuit breaker.
- Cables with 1,5 mm² section wires are to be used for the power supply, electric motor and flasher for distances up to 50 m.
- Cables with 1 mm² section wires are to be used for the limit switches, photocells, push buttons and accessories.
N.W.: for applications such as light switching, CCTV, etc. use solid state relays to prevent the microprocessor from being affected.
IN CASE OF FAILURE OF THE PANEL:
- Check the electronic PCB voltage supply is 230 V ±10%.
- Check the electric motor power supply is 230 V ±10%.
- For longer distances increase wire section.
- Check fuses.
- The photocell contacts are closed.
- Check all NC contacts.
- The limit switches are properly connected and work correctly.
- In case the electric valve is fitted, check integrity with all fuses.
- Check that no voltage drop has occurred from the control board to the electric motor.
1
2
3
4
1 2
3 4
ELPRO S40
ELPRO
S40
VERS.
ON
OFF
1
2
3
4
5
6
7
8
9 10 11 12
52
51
53
SYMBOLS:
NO
contact
NC
contact
Led
ON
Led
OFF
Pilot light
Flasher
-
+
-
+
GB
ELECTRONIC CONTROLLER UP TO 4 AUTOMATIC BOLLARDS,
WITH OR WITHOUT LIMIT SWITCH
istr_elpro-s40_GB.ai 2 07/07/2023 16:05:43
Summary of Contents for Elpro S40
Page 38: ...Elpro S40 38...
