FAAC E1SL, Manual, Page: 29 / 52

20
21
22
E1SL 29 532258 04 - Rev. B
E1SL
ID3
ID11 ID12
S
S
S
S
S
S
S
S
AIRSLIDE AIRSLIDE
INTERLOCK
INTERLEAVES
INTERLEAVES
B
A
E1SL
ID4
E1SL
ID2
E1SL
ID1
SDK EVO
INTERLOCK
E1SL E1SL
1 3
INTERLEAVES
E1SL E1SL
1 2
3 4
5 6
7 8
AIRSLIDE
E1SL E1AS (DIP switch)
1 9
2 10
3 11
4 12
5 13
6 14
7 15
G CH CL G G CH CL G
J18 / J2 J18 / J2 J18 / J2
G CH CL G
0 DL11
USB
F
ERR
BAT1
OPEN
EMERG
BAT2
SIC_OP
SIC_CL
J13
V G
S1
G
T
J1
V RX
TX G
J8
E1 G E2 J7
T1 G
T2
R1
G R2
J9
V G 01 02 02
J22
J21
V
G
I1
I2
G
I3
I4
V
J18
G CH CL
G
J23 J24
J25
V G
S2
G
T
J4
J18
Tr
ansla
tion of the original instruc
tions
ENGLISH
Example of INTERCOM network on 2 accesses (A and B) that both require 2
INTERLEAVES automations. The automatons on access B, that faces the outside, are
fitted with AIRSLIDE. A and B are interlocked (INTERLOCK mode): one access can
open only when the other is closed.
INTERCOM connection with boards in a cascade configuration
J18 E1SL, E1RD
J2 AIRSLIDE
Internal
External
 8
Pre-set ID associations
INTERCOM is the network made up of interconnected boards that are
programmed via the SDK EVO. INTERCOM manages up to 15 boards
(referred to as
NODES ) that are identified by different ID numbers. See
the example of a typical INTERCOM configuration (
20
).
INTERCOM allows you to:
- select the operating mode for the entire network
In addition, INTERCOM allows you to create:
- INTERLOCK : 2 interlocked automations: the opening of one automa-
tion is subject to the closing of the other and vice versa
-
INTERLEAVES 2 automations that work simultaneously to cover an
access (simultaneous opening / closing)
-
AIRSLIDE an automation with an AIRSLIDE device
INSTALLING INTERCOM
1. Connect all the boards together using 3 wires in a cascade con-
figuration, in any order, to the dedicated connectors.
2. Connect the SDK EVO to each individual board ( NODE ) to assign
the ID and enable INTERLOCK, INTERLEAVES, AIRSLIDE where
required (relative
§ Sections).
-
It is important to specify which is the MASTER board (ID1).
3. Connect the SDK EVO to the MASTER board to register all the
network IDs.
ASSIGNING AN ID
-

/ PROGRAMMING /INTERCOM/ ID : select ID 1 - 15
Assign a different ID to each board. There must be a board with
ID 1 ( MASTER ). If INTERLOCK, INTERLEAVES, or AIRSLIDE operation is
required, keep to the pre-set ID associations (tables in
22
), other-
wise they can be assigned as you choose.
OPERATION
Using the MASTER board via the SDK EVO or a configured input, it is
possible to:
- set the operating mode for the entire network
- enable/disable INTERLOCK
TEMPORARILY DISABLING A BOARD
A board can be temporarily excluded from the network operating
mode via the
MASTER board:
-

/ PROGRAMMING /INTERCOM/ NODE LIST … (select the ID)
… MAINTENANCE select:
LOCAL : you can set the operating mode on the selected board (not possible for ID1)
MANUAL : the selected board goes into MANUAL operating mode.
DISABLED : the selected board resumes the operating mode of the network
INTERCOM DIAGNOSTICS
Each board in the network can be checked using the MASTER board.
-

/ PROGRAMMING /INTERCOM/ NODE LIST (registered IDs )
- select an ID and press OK to display INFO, ERRORS, WARNINGS, CYCLES NUMBER .
ID…(*) = ID temporarily excluded from the network
ID…(!) = ID error
9. INTERCOM
J18
G CH CL
G
G GND Accessories power supply negative and Common contacts
CH INTERCOM
CL INTERCOM
G GND Accessories power supply negative and Common contacts