J7
J8
J4
J1
J2
J5
J3
J12
DS1
SET UP
OPEN
LD6
LD5
LD4
OPEN B
OPEN A
LD3
LD2
LD1
4.3 Terminal-boards and connectors
4.2 E064 board components
4 E064 CONTROL BOARD
4.1 Technical specifications
Fig. 1
4.4 DS1 Programming dip-switches
4.5 Operating logics
Logic A (automatic)
Logic E (semi-automatic)
(1) Prevents closing if pulse is maintained.
(2) Prevents closing and/or opening if pulse is
maintained.
Description
Connected device
OPEN A
Command device with N.O. contact
(see chap. OPERATING LOGICS)
STOP
Device with N.C. contact which stops the
automated system
Negative for OPEN A and STOP devices
FSW
Closing safety device with N.C. contact (see
chap. OPERATING LOGICS)
LAMP
OPEN COLLECTOR 24 Vdc 100 mA. output for
flashing lamp
-TX FSW
Negative for powering safety accessories (FAIL
SAFE function)
Negative for powering accessories
+24 Vdc for powering accessories
No. Function
OFF
ON
1 Fail Safe
Enabled
Not enabled
2 Anti-crushing sensitivity
Low
High
3 Not used
/
/
4 Carriage speed
High
Low
Status
Open (pulse)
Stop
Fsw
CLOSED
Opens and closes
after pause time
No effect (2)
No effect
OPENING
No effect
Locks (2)
No effect (1)
OPEN IN
PAUSE
Resumes counting of
pause time (1)
Locks (1)
Resumes counting of
pause time (1)
CLOSING
Reverses motion
Locks (2)
Reverses motion
LOCKED
Closes
No effect (2)
No effect (1)
Status
Open (pulse)
Stop
Fsw
CLOSED
Opens
No effect (2)
No effect
OPENING
Locks
Locks (2)
No effect (1)
OPEN
Closes
No effect (2)
No effect (1)
CLOSING
Reverses motion
Locks (2)
Reverses motion
LOCKED
Closes
No effect (2)
No effect (1)
Supply voltage (V ~ / Hz.)
230 / 50
Power supply to accessories (Vdc)
24
Accessories max. load (mA.)
200
Operating ambient temperature (°C)
-20 / +55
Quick-fit connector
for receiver boards XF433 /
XF868 and battery module
Operating logics
Automatic / Semiautomatic
Terminal-board connections
Open/Stop/Safety devices/Fail-
safe/Flashing lamp 24 Vdc
Courtesy light timer (min.)
2
J1
Low voltage inputs/accessories terminal board
J2
Quick-fit connector for receivers XF433 or XF868
J3
230V power supply input terminal board
J4
Connector for transformer primary winding
J5
Courtesy light terminal-board
J7
Connector for transformer secondary winding
J8
Motor output connector
J12
Battery module connector
OPEN A
Radio signal programming push-button
OPEN B
Radio signal programming push-button
OPEN
OPEN push-button
SETUP
SET-UP push-button
DS1
Programming dip-switch
LD1
Signalling LED: OPEN input
LD2
Signalling LED: STOP input
LD3
Signalling LED: FSW input
LD4
Signalling LED: SET UP cycle
LD5
LED signalling memory-storage: radio channel OPEN A
LD6
LED signalling memory-storage: radio channel OPEN B
Fail Safe
If activated, it enables the photocell operating test before every
movement.
Operating logics
For doors with an irregular movement, it reduces the sensitivity of
the anti-crushing device to prevent unwanted action by it.
