manualshive.com logo in svg

F.W. Bell 8000 series, Instruction Manual

Share
Download
F.W. Bell 8000 series Instruction Manual Download Page 112

F.W. BELL    8000 Series     Gauss/Tesla Meter Instruction Manual 
 

 

Section 8 – Remote Operation 

 

8-33

 

:CALCulate#:LIMit:FAIL? 

Returns the pass/fail status of the classifier test. A “0” indicates that the 
measured value falls between the lower and upper limit and is considered a 
“pass” situation.   A “1” indicates that the measured value either falls below 
the lower limit or above the higher limit. 

 

 

Measurement 
Commands 

Since these commands are channel-specific the “#” in each command 
should be replaced with the channel number 1,2 or 3.  If the channel 
number is omitted then Channel-1 is assumed. 
 

:MEASure#:FLUX? 

Returns the latest flux density reading, the value will be between 
0.0000000000 and 

±

 29999999.  The meaning of this value depends upon 

the selected unit of measure (gauss, tesla, etc.).  For instance the value 
1.0203 could mean 1.0203 G or 1.0203 T.  The rate at which flux density 
readings are updated is controlled by the display update rate. Issuing the 
MEASure:FLUX? command at a rate that is faster than this update rate 
will return the same reading multiple times.  For instance, if the meter 
updates the reading once per second, and the MEASure:FLUX? 
command is issued 10 times per second, the same reading may be 
returned 10 times before a new reading is available.  If no probe is present 
the string NPC is returned. 

 

 

:MEASure#:FLUX:FAST? 

Similar to the normal MEASure:FLUX? command but will return values at 
the rate determined by the :MEASure:FLUX:FAST:RATE setting. If no 
probe is present the string NPC is returned. At faster update rates 
accuracy may be reduced from that specified for the displayed values.

 

 
:MEASure#:FLUX:STReaming? <n>

 

Returns a stream of the latest flux density readings at the rate set by the 
display update rate for a period of time <n> in seconds. 
 

:MEASure#:FLUX:STReaming:FAST? <n>

 

Returns a stream of the latest flux density readings at the rate determined 
by the :MEASure:FLUX:FAST:RATE setting for a period of time <n> in 
seconds.  If no probe is present the string NPC is returned.  
 

:MEASure#:FLUX:FAST:RATE <n> 

Specify the reading update rate for the FAST flux measurement 
commands; (n = desired readings per second; valid values are from 0.5 
through 50.0, default is 10.0). 

Maximum speed may be limited by 

slower baud rate settings. 

NOTE: The maximum rate is limited to 12/sec for the 0.5-500Hz and 16-
500Hz AC Bandwidth settings or if a MOS type low field probe is used. 
 

:MEASure#:FLUX:FAST:RATE? 

Query the presently defined FAST reading update rate setting. 
 
 

Summary of Contents for 8000 series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands