F.F. Group RH 5-32 PRO, Original Instructions Manual

Page: 9 / 44

tool. Loss of control can cause personal injury.
f
Hold power tool by insulated gripping surfac -
es, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a “live”
wire may make exposed metal parts of the power
tool “live” and could give the operator an electric
shock.
f
Use suitable detectors to determine if utility
lines are hidden in the work area or call the lo-
cal utility company for assistance. Contact with
electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pene-
trating a water line causes property damage or may
cause an electric shock.
f
when working with the machine, always hold it
firmly with both hands and provide for a secure
stance. The power tool is guided more secure with
both hands.
f
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure
than by hand.
f
Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over the
power tool.
PRODUCTS SOLD IN GB ONLY: Your product is
fitted with a BS 1363/A approved electric plug
with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fit -
ted in its place by an authorised customer service
agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be insert-
ed into a mains socket elsewhere.
CONNECTION TO THE POwER SUPPLY
Make sure the power supply information on the
machine’s rating plate are compatible with the
power supply you intend to connect it to.
This appliance is Class II* and is designed for con-
nection to a power supply matching that detailed
on the rating label and compatible with the plug
fitted. If an extension lead is required, use an ap -
proved and compatible lead rated for this appli-
ance. Follow all the instruction supplied with the
extension lead.
*Double insulated: This product requires
no earth connection as supplementary in-
sulation is applied to the basic insulation to
protect against electric shock in the event of
failure of the basic insulation.
GUIDELINES FOR USING EXTENSION CORDS
f
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
f
Always replace a damaged extension cord or have it
repaired by a qualified person before using it.
f
Protect your extension cords from sharp objects,
excessive heat and damp/wet areas.
f
Use a separate electrical circuit for your tools. This
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF
position and the electric voltage is rated the same
as the voltage stamped on the motor nameplate.
Running at a lower voltage will damage the motor.
PRODUCT SPECIFICATIONS
INTENDED USE
The machine is intended for hammer drilling in con-
crete, brick and stone as well as for chiselling.
TECHNICAL DATA
Article number 45 308 45 309
Model RH PRO 6-35MX 5-32
Rated voltage
V 230
Hz 50
Rated power input W 1.100
No-load speed min
-1
300-760
Impact rate min
-1
1950-
4860
1900-
4800
Impact energy J 1-7 1-6
Chuck type SDS-max
SDS-
plus
Tool holder 35 32
Weight kg 6,1 5,8
Max. drilling Ø
Concrete mm 35 32
Sound emission values determined according
to EN 60745-1, EN 60745-2-6
Typically the A-weighted noise levels of the
product are:
Sound pressure
level
dB(A) 90,86
Sound power level dB(A) 101,86
Uncertainty K dB 3
Vibration total values a
h
(triax vector sum)
and uncertainty k determined according to EN
60745-1, EN 60745-2-6
Vibration level max:
a
h
m/s
2
17,901
K m/s 2 1,5
IDENTIFICATION
1. Dust protection cap
2. Locking sleeve
3. Power On Indicator
4. Mode selector switch
5. On/Off switch
6. Handle (insulated gripping surface)
7. Thumbwheel for speed preselection/impact
frequency preselection
8. Service indicator
9. Auxiliary handle (insulated gripping surface)
English | 9
www.ffgroup-tools.com
RH 6-35 MX PRO | RH 5-32 PRO