F.F. Group BPS 25/40V PLUS, Original Instructions Manual

Page: 13 / 64

BPS 25/40V PLUS
www.ffgroup-tools.com
English | 13
flammable surfaces (e.g., paper, textiles, etc.) or
surroundings. The heating of the battery charger
during the charging process can pose a fire hazard.
f
Do not cover the ventilation slots of battery
charger. Otherwise, the battery charger can over-
heat and no longer operate properly.
PRODUCT SPECIFICATIONS
INTENDED USE
The machine is intended for domestic use, for pruning
trees and shrubs at elevated height, while the user is
situated on the ground. The machine is not intended
to cut inorganic material or to be used on a ladder or
steps. This tool is not intended for commercial or in-
dustrial use.
TECHNICAL DATA
Article Number 42 407
Model BPS 25/40 PLUS
Motor Brushless
Rated voltage V 36 (40max)
No load speed rpm 4.800 - 5.280
Chain speed m/s 9,5
Blade length mm 254
Max Reach m 3
Run Time min 25
No load running time min 70
Oil reservoir capacity ml 80
Weight Kg 4,6
Chain bar Model (100SDEA041) 254mm
Saw chain model (91P040X) 254mm
Battery model
(not included)
BLi 40V/5.0Ah
Charger model
(not included)
CH 40V/2A
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
Sound pressure level dB(A) 76,3
Guaranteed sound
power level
dB(A) 95
Uncertainty K dB 2,5
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to EN
60745-1
Vibration level max:
a
h ,HD
m/s 2 1,542
K m/s 2 1,5
IDENTIFICATION
1. Battery slot
2. Safety switch
3. Trigger
4. Pole
5. Telescoping release clasp
6. Angle adjustment button
7. Motor housing
8. Chain-tensioning ring
9. Cover Release Knob
10. Oil tank cover
11. Guide Bar
12. Saw Chain
13. Chain guard
14. Harness
PREPARING FOR USE
DANGER! To avoid serious personal injury, do
not operate the chainsaw without the chain
bar, saw chain, and side cover properly as-
sembled.
WARNING: Do not attempt to operate the
chainsaw if any part is damaged or missing.
FILLING THE BAR AND CHAIN OIL RESERVOIR
IMPORTANT! Bar and chain oil prevents pre-
mature wear. Never operate the chainsaw if
oil is not visible in the inspection window.
Check oil level frequently and fill as needed.
f
Bar and chain oil is required to properly lubricate the
chain bar and saw chain. The chainsaw is equipped
with an automatic oiler that deposits oil on the bar
and chain when running, keeping them properly
lubricated. It is specially designed to provide low
friction and faster cuts. NEVER use oil or other lu-
bricants that have not been specifically designed for
use on the bar and chain. This can lead to a clogged
oil system which may cause premature wear of the
bar and chain.
f
Place the chainsaw on a firm, flat surface so that the
oil cap (10) is on top.
ƒ
Clean any debris from the cap area.
ƒ
Remove the cap (10) .
ƒ
Carefully pour the bar and chain oil into the res-
ervoir.
ƒ
Replace the cap and make sure oil is visible in the
reservoir.
TENSIONING THE SAW CHAIN
WARNING: If the chain is still loose when the
saw is at maximum tension, replace the chain.
IMPORTANT! Only tension the saw chain
when the chain is cool. A hot chain may con-
tract and damage the chain bar or chain as it
cools.
Wear gloves.
ƒ
Remove the battery before tensioning.
ƒ
Loosen the side cover release knob (9) slightly,
but do not remove the side cover.
ƒ
Hold up the nose of the chain bar (E) and turn
the chain tensioning ring (8) clockwise.
ƒ
Tighten the chain tensioning ring until the low-