| English
8
AG 115/750 PLUS
PRODUCT
SPECIFICATIONS
INTENDED USE
The machine is intended for cutting, roughing and
brushing of metal and stone materials without the
use of water.
TECHNICAL DATA
Article number
41628
Model
AG 115/750 PLUS
Rated voltage
V
230-240
Hz
50/60
Rated power input
W
750
Rated speed
min
-1
12.000
Grinding disc diameter, max.
mm
115
Thread of grinder spindle
M
14
Thread length (max.) of
grinder spindle
mm
11,5
Weight
kg
1,7
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
Sound pressure level
dB(A)
90
Sound power level
dB(A)
101
Uncertainty K
dB
3
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to EN
60745-1
Vibration level max:
a
h,AG
m/s
2
6,559
K
m/s
2
1,5
NOISE/VIBRATION INFORMATION
The vibration level given in this information sheet
has been measured in accordance with a standard-
ized test given in EN 60745 and may be used to
compare one tool with another. It may be used for
a preliminary assessment of exposure. The declared
vibration emission level represents the main appli
-
cations of the tool. However if the tool is used for
different applications, with different accessories or
insertion tools or is poorly maintained, the vibration
emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not
actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organization of work patterns.
IDENTIFICATION
1.
On/Off switch
2. Spindle lock button
3. Auxiliary handle
4.
Protective guard
5.
Protective guard screw
6. Spindle
7.
Clamping flange
8. Spanner
9.
Mounting flange
USE
MOUNTING OF ACCESSORIES (E)
h
Clean spindle
(06)
and all parts to be mounted.
h
Tighten clamping flange
(07)
with spanner
(08)
while
pushing spindle-lock button
(02)
.
h
For removing accessories handle vice-versa.
MOUNTING OF AUXILIARY HANDLE (C)
Screw the auxiliary handle
(03)
on the right or left of
the machine head depending on the working method.
REMOVING / MOUNTING / ADJUSTING OF PRO-
TECTIVE GUARD (B)
h
Open protective guard
(04)
by loosening screw
(05)
h
Place protective guard
(04)
on the spindle collar of the
tool head and turn it to the required position (depend
-
ing on the work to be carried out).
h
Fasten protective guard
(04)
by tightening screw
(05)
BEFORE USING THE TOOL
h
Ensure that accessory is correctly mounted and firmly
tightened.
h
Check if accessory runs freely by turning it by hand.
h
Test-run tool for at least 60 seconds at highest no-load
speed in a safe position.
h
Stop immediately in case of considerable vibration or
other defects and check tool to determine the cause.
SWITCHING ON AND OFF (D)
h
To start the power tool, push the on/off switch
(01)
forward.
h
To lock the on/off switch
(01)
in position, push the on/
off switch
(01)
forward and down until it clicks into
place.
h
To switch off the power tool, release the on/off switch
(01)
; or, if the switch is locked, briefly push the on/off
switch
(01)
backward and down and then release it.
ROUGH GRINDING
h
The best roughing results are achieved when setting
the machine at an angle of 30° to 40°. Move the ma
-
chine back and forth with moderate pressure. In this
manner, the workpiece will not become too hot, does
not discolour and no grooves are formed.
h
Never use a cutting disc for roughing.
CUTTING
h
Do not tilt the tool while cutting.
h
Always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner.
h
Do not apply pressure on the tool; let the speed of the
cutting disc do the work.
h
The working speed of the cutting disc depends on the
material to be cut.
h
Do not brake cutting discs with side pressure.
MAINTENANCE
Regular inspection and cleaning reduces the neces-
Summary of Contents for AG 115/750 PLUS
