background image

*$62/,1(32:(5('3(56211(/&$55,(56 *2/)&$5

Page 17

Owner’s Manual and Service Guide

Read all of manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notes, Cautions and Warnings

CARE AND CLEANING OF THE VEHICLE

T

o prevent cosmetic damage, do not

use any abrasive or reactive solvents to

clean plastic parts. 

It is important that proper techniques and cleaning mate-
rials be used.

Normal cleaning of vinyl seats and plastic or rubber trim
require the use of a mild soap solution applied with a
sponge or soft brush and wiping with a damp cloth.

Removal of oil, tar, asphalt, shoe polish, etc. will require
the use of a commercially available vinyl/rubber cleaner.

The painted surfaces of the vehicle provide attractive
appearance and durable protection. Frequent washing
with lukewarm or cold water is the best method of pre-
serving the painted surfaces.

Do not use hot water, strong soap or harsh chemical
detergents.

Rubber parts should be cleaned with non-abrasive
household cleaner.

Occasional cleaning and waxing with non-abrasive prod-
ucts designed for ‘clear coat’ automotive finishes will
enhance the appearance and durability of the painted
surfaces.

Corrosive materials used as fertilizers or for dust control
can collect on the underbody of the vehicle. These mate-
rials could cause corrosion of underbody parts. It is rec-
ommended that the underbody be flushed occasionally
with plain water. Thoroughly clean any areas where mud
or other debris can collect. Sediment packed in closed
areas should be loosened to ease removal, taking care
not to chip or otherwise damage paint. 

If the engine does not start or runs improperly
after washing, remove the spark plug wires (by

pulling the spark plug boots, never the wires) and blow them
dry. Reinstall the wires. Remove moisture from coil by blowing
across top. 

VEHICLE CARE PRODUCTS

To help maintain the vehicle, E-Z-GO has several prod-
ucts, available through a local Distributor, an E-Z-GO
Branch, or the E-Z-GO Service Parts Department,
among them are:

Touch-up paint specially formulated to match vehi-
cle colors for use on both metal and TPE (plastic)
bodies. (P/N28140-G** and 28432-G**)

Multi-purpose Battery Protectant formulated to
form a long-term, flexible, non-tacky, dry coating

that will not crack, peel or flake over a wide tem-
perature range. (P/N 75500-G01)

White Lithium Grease designed to provide lubrica-
tion protection in areas where staining or discolor-
ing is a problem, or in areas of extreme
temperature ranges. (P/N 75502-G01)

Penetrant/Lubricant, a 4-in-1 product that pene-
trates the most stubborn of frozen parts, lubricates
leaving a light lubricating film, prevents corrosion
by adhering to wet or dry surfaces and displaces
moisture, sealing against future moisture return.
(P/N 75503-G01)

Multi-purpose Cleaner and Degreaser that con-
tains natural, environmentally safe solvents. (P/N
75504-G01)

Multi-purpose Hand Cleaner is an industrial
strength cleaner containing no harsh solvents, yet
gently lifts grease off hands. May be used with or
without water. (P/N 75505-G01)

Battery Cleaner that promotes easy, non-violent
neutralization of battery acids and battery acid
crystals. The resulting sodium salts are water sol-
uble and easily washed away. (P/N 75506-G01)

Biodegradable Cleaner that cleans the toughest
dirt and heavy soils by breaking down grease to
be easily wiped or rinsed away. (P/N 75507-G01)

Multi-purpose Value Pack sampler package
including 4 ounce (118 ml) aerosol cans of Battery
Protector, Penetrant/Lubricant, White Lithium
Grease, and Carburetor and Choke Cleaner. (P/N
75508-G01)

Plexus plastic cleaner and polish removes minor
scratches from windshield. (P/N 28433-G**)

TOP AND WINDSHIELD

The top does not provide
protection from roll over
or falling objects.

The windshield does not provide protection from tree
limbs or flying objects.

Clean with lots of water and a clean cloth. Minor
scratches may be removed using a commercial plastic
polish or Plexus plastic cleaner available from E-Z-GO.

!

!

Summary of Contents for SHUTTLE 4

































































Reviews: