X6$
= Port timeout (10‑sec. increments)
1
(= 10 seconds) –
65000
(default is
30
= 300 seconds = 5 minutes)
X6%
= SMNP port number
00000
(= disable) –
nnnnn
. Default =
00161
. Leading zeroes are not necessary for entry.
X6^
= SNMP contact name and location Up to 64 alphanumeric characters. Default =
Not
•
Specified
.
X6&
= SNMP community name
Up to 64 alphanumeric characters.
Default =
public
(for read community) or
private
(for read‑write community).
X6*
= Trap target
1
–
3
X6(
= SNMP trap version
2
or
3
, or
0
= empty (
default
) if no target set
X7)
= SNMP target 1 through 3
70
–
72
.
70
= SNMP target 1, ...
72
= target 3
Command and Response Table for IP- and SNMP-Specific SIS Commands
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
IP setup commands
Set matrix name
EX4)
CN
}
Ipn
•
X4)]
Read matrix name (location)
E
CN
}
X4)]
Reset matrix name to factory default
E
•
CN
}
Ipn
•
X4)]
“
FOX-Matrix-3
(
7
)‑”
plus the last
3 pairs of the MAC address.
Set time and date
E
X4@
CT
}
Ipt
X4@]
Read time and date
E
CT
}
X4#]
Set GMT offset
EX4$
CZ
}
Ipz
X4$]
In the command, the divider between
hours and minutes can be either a
colon or a period. In the response, the
divider is a colon.
Example:
E
8.3CZ
}
Ipz+08:30
]
8
.
3
= 8:30
Read GMT offset
E
CZ
}
X4$]
Set Daylight Saving Time
EX4%
CX
}
X4%]
Read Daylight Savings Time
E
CX
}
X4%]
Set IP address
EX4^
CI
}
Ipi
X4^]
Read IP address
E
CI
}
X4^]
Read hardware address
E
CH
}
X4&]
Reads MAC address.
Read # of open connections
E
CC
}
X4*]
Set subnet mask
EX4^
CS
}
Ips
X4^]
Read subnet mask
E
CS
}
X4^]
Set gateway IP address
EX4^
CG
}
Ipg
X4^]
Read gateway IP address
E
CG
}
X4^]
Set administrator password
EX4(
CA
}
Ipa
•
X4(]
Read administrator password
E
CA
}
X4(]
Reset (clear) administrator
password
E
•
CA
}
Ipa
•
]
Set user password
EX4(
CU
}
Ipu
•
X4(]
Read user password
E
CU
}
X4(]
Reset (clear) user password
E
•
CU
}
Ipu
•
]
Set mail server, domainname
EX4^
,
X5)
,
X4(
CM
}
Ipm
X4^
,
X5)
,
X4(]
Read mail server, domainname
E
CM
}
X4^
,
X5)
,
X4(]
Set e‑mail recipient
EX5!
,
X5@
CR
}
Ipr
X5!
,
X5@
,
]
This command sets the e‑mail recipient.
To receive e‑mail notifications, you must
then set the events that the switcher
reports, using one or more separate
Set e-mail
(EM) SIS commands (on the
next page).
Example:
E
}
Ipr69,[email protected],
]
Read e‑mail recipient
EX5!
CR
}
X5@
,
]
FOX Matrix 3200 and 7200 Switchers • Programming Guide
68
Summary of Contents for FOX Matrix 3200
Page 6: ......
