EVOC P19 Series Manual Download Page 90

Page: 90 / 131

BIOS Setup (Applicable to ECS-1838

motherboard)

P19 SERIES

· 81 ·

must be LOGO.BMP.



Special Boot Order Configuration

This option provides EVOC special boot order configuration.



Special Boot Order Configuration

The control switch of EVOC special boot order function. Only when this option is

set to “Enabled”, can the boot order be configured.



HDD eSMART Configuration

To enable or disable monitoring of health status of SATA HDD device, which is a

dynamic detection option. After the motherboard is connected with an HDD, the

corresponding SATA Port will display the monitored parameters. If no SATA storage

device is connected, SATA Port indicates “Empty”.

Note: This is function is effective only when “Advanced

→

SATA Configuration

→

SATA Mode Selection” option is set to “IDE”.

This function is disabled by default.

Summary of Contents for P19 Series




































































































































Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands

EVOC P19 Series, Manual

Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands