EVOC P19 Series Manual Download Page 49

Page: 49 / 131

Expansion Installation

· 40 ·

P19 SERIES

8.3 Installing/Removing the MiniPCI-E.M-SATA

Note:MiniPCI-E,M-SATA all support 3G/4G module.

Preparation Work

Disconnect the PC from power source.

Caution

The electronic components on the PCB are extremely sensitive to ESD.When operating

these components,make sure to take proper preventative measures.Please see the "ESD

Guideline"for regulations related to operation of ESD-sensitive components.

Removing the MiniPCI-E.M-SATA

Steps to remove MiniPCI-E.M-SATA

With ECS-1837/1838

With ECS-1840/1841

Remove the four screws shown in the

picture,to separate the display and

chassis.

Remove the four screws shown in the

picture,to separate the display and

chassis.

Take out MiniPCI-E.M-SATA

Summary of Contents for P19 Series




































































































































Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands

EVOC P19 Series, Manual

Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands