EVOC P19 Series Manual Download Page 74

Page: 74 / 131

BIOS Setup (Applicable to ECS-1837

motherboard)

P19 SERIES

· 65 ·

7,otherwise blue screen would be occur when the system is installed, or the installed

system cannot be booted.

Note: Android option is only used for testing.Due to lack of corresponding driver,the

current Android system is not fully supported.



USB Configuration



Legacy USB Support

This option is used to support legacy USB devices (keyboard, mouse, storage device,

and etc.). When this option is set to Enabled, even under operating systems that do not

support USB, such as DOS, USB device can still be used. When it is set to Disabled,

legacy devices cannot be used in operating systems that do not support USB.

Note: USB can still be used under EFI application, such as under Shell.



XHCI Hand-off

If this option is used for operating system that does not have USB3.0 driver, this

option enabled means that the system will switch to BIOS XHCI.



EHCI Hand-off

If this option is used for operating system that does not have USB2.0 driver, this

option enabled means that the system will switch to BIOS EHCI.



USB Mass Storage Drive Support

SB mass storage USB support option. It is ENABLED by default.

Summary of Contents for P19 Series




































































































































Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands

EVOC P19 Series, Manual

Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands