EVOC P19 Series Manual Download Page 130

Page: 130 / 131

BIOS Setup (Applicable to ECS-1841

motherboard)

P19 SERIES

· 121 ·



User Password

This option is used to set up user password.

Note: If only the user password is set, administrator authority can be obtained after

the password is keyed in when entering Setup program. At this time, empty

password is ineffective.



Boot



Setup Prompt Timeout

Setup prompt waiting time after pressing F2.



Bootup NumLock State

To set whether Numlock state is enabled during bootup.



Quiet Boot

Boot mode selection switch, used to enable or disable Quiet Boot function.



Boot Option Priorities

This option is used to configure priorities for system boot. Among them, #1 represents

highest priority, #n represents lowest priority.



Fast Boot

To enable or disable Fast Boot function.

Summary of Contents for P19 Series




































































































































Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands

EVOC P19 Series, Manual

Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands