EVOC P19 Series Manual Download Page 106

Page: 106 / 131

BIOS Setup (Applicable to ECS-1840

motherboard)

P19 SERIES

· 97 ·



Legacy USB Support

This option is used to support legacy USB devices(keyboard,mouse,storage device,and

etc.)When this option is set to Enabled,even under operating systems that do not

support USB,such as DOS,USB device can still be used.When it is set to Disabled,

legacy devices cannot be used in operating systems that do not support USB.

Note:USB can still be used under EFI application, such as under Shell.



XHCI Hand-off

If this option is used for operating system that does not have USB3.0 driver, this

option enabled means that the system will switch to BIOS XHCI.



EHCI Hand-off

If this option is used for operating system that does not have USB2.0 driver, this

option enabled means that the system will switch to BIOS EHCI.



USB Mass Storage Drive Support

USB mass storage USB support option. It is ENABLED by default.



USB transfer time-out

USB transfer time-out is 20S[1/5/10/20] by default.



Device reset time-out

Device reset time-out is 20S[10/20/30/40] by default.



Device power-up delay

Device power-up delay [AUTO/MANUAL].

Summary of Contents for P19 Series




































































































































Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands

EVOC P19 Series, Manual

Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands