EVOC P19 Series Manual Download Page 62

Page: 62 / 131

PC Maintenance

P19 SERIES

· 53 ·

11.1.3 Replacing Backup Battery

Things to know before changing battery

Caution

Damage may exist!

Always use same type lithium battery or lithium batteries recommended by the

manufacturer.

Disposal

Caution

Battery to be discarded should be disposed according to local laws.

Preparation Work

Notes:

1.Note down the current BIOS Setup or save the settings to the user profile in the BIOS

Setup“Exit” menu.

2. BIOS Setup provides a list, where these information can be saved.

3. Disconnect the PC from power source.

Replacing Battery

Steps to replace battery

Loosen the four screws on the top cover, and open the top cover.

Pull out the battery connection

cable as shown in the picutre,

and remove the battery.

Summary of Contents for P19 Series




































































































































Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands

EVOC P19 Series, Manual

Search results

Summary of Contents for P19 Series

Reviews:

Related manuals for P19 Series

Brands by name

Popular brands