Eton VECTOR 250 - SERVICE Service Manual Download

Page: 71 / 154

Installation of Clutch OUTER/Driven Pulley
Assembly

Install new oil seal and O-ring onto movable driven

face.

Apply with specified grease to lubricate the inside

of movable driven face.

Install the movable driven face onto driven face.

Install the guide pin and guide pin roller.

Install the collar.

Install friction plate, spring and clutch weight into

clutch spring compressor, and press down the

assembly by turning manual lever until mounting

nut that can be installed.

Hold the compressor by bench vise and tighten

the mounting nut to specified torque with clutch

nut wrench.

Remove the clutch spring compressor.

Torque value: 5.0~6.0kgf-m

Install clutch outer/driven pulley and drive belt onto

drive shaft.

Collar

O-ring Guide

pin

Guide pin roller

Guide pin

Oil seal

O-ring

Specified grease

Movable driven face

Clutch spring compressor

Clutch nut wrench

Summary of Contents for VECTOR 250 - SERVICE



























































































































































Search results

Summary of Contents for VECTOR 250 - SERVICE

Reviews:

Related manuals for VECTOR 250 - SERVICE

Brands by name

Popular brands

Eton VECTOR 250 - SERVICE, Service Manual

Search results

Summary of Contents for VECTOR 250 - SERVICE

Reviews:

Related manuals for VECTOR 250 - SERVICE

Brands by name

Popular brands