manualshive.com logo in svg

Eton VECTOR 250 - SERVICE, Service Manual, Page: 148 / 154

Share
Download
Eton VECTOR 250 - SERVICE Service Manual Download Page 148

 148

 

17.7 Instrument Panel 

 

The instrument panel includes fuel gauge, speed meter, water 
Temperature gauge, right and left turn signal, trip do-meter,   
and indicator camp. A LCD is used on ATV8

E

’s instrument panel 

to display all driving information for users. Therefore, this is an 
all-in-one instrument panel. 

 
 
 
 
 
 
 

 Instrument Panel

 REMOVAL 

There is a cable and connector on the back of the   
instrument panel.  After removing instrument panel,   
users can find out   
an electrical connector which is connected with a driving 
sensor at the back of the instrument panel.   
 
 

 
 
 
 
 
 
 
 
 

 
 
The sensor is installed at the brake disk and a cable is tightened 
on the left side of knuckle component   
as shown in pictures 
 
 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sensor 

Cable 

Summary of Contents for VECTOR 250 - SERVICE



























































































































































Reviews:

No comments